Resistors

Configurable Analog Front-End (AFE) Potentiostat for Electrochemical Sensors – Ultra-low-power programmable analog front-end designed for electrochemical gas sensors, toxic gas detection, air quality monitoring, industrial safety systems, wearable health devices, environmental monitoring, and embedded sensing applications. The Texas Instruments LMP91000 integrates a complete potentiostat and transimpedance amplifier (TIA), enabling direct interfacing with 2-electrode galvanic and 3-electrode amperometric chemical sensors. Operates from a 2.7 V to 5.25 V supply while consuming less than 10 µA typical supply current, making it ideal for battery-powered systems. Features a programmable TIA gain (2.75 kΩ to 350 kΩ), programmable load resistor, programmable cell bias, I²C-compatible interface, integrated temperature sensor, sensor diagnostics, and support for sensor currents from 5 µA to 750 µA full scale. Housed in a compact 14-pin WSON (4 × 4 mm) package and specified for operation over a −40°C to +85°C temperature range. #TexasInstruments #LMP91000SDXNOPB #LMP91000 #AnalogFrontEnd #Potentiostat #ElectrochemicalSensor #GasSensor #AirQualityMonitoring #IndustrialSafety #I2C #LowPower #EmbeddedSystems

Adjustable Low-Dropout (LDO) Linear Voltage Regulator – Positive adjustable LDO voltage regulator designed for power supplies, industrial control systems, embedded electronics, consumer devices, communication equipment, and analog circuits. Delivers up to 800 mA output current with an adjustable output voltage range of 1.25 V to 13.8 V using an external resistor divider. Operates from an input voltage up to 15 V with a maximum dropout voltage of 1.2 V at 800 mA, making it suitable for low-dropout linear regulation. Features 1% output voltage accuracy, 75 dB PSRR (120 Hz), 5 mA typical quiescent current, current limiting, and thermal shutdown protection for reliable operation. Designed for surface-mount applications in a TO-252-3 (DPAK) package and operates over a 0°C to +125°C temperature range. #TexasInstruments #LM1117DTADJNOPB #LM1117 #LDO #LinearRegulator #VoltageRegulator #AdjustableRegulator #PowerManagement #DPAK #EmbeddedSystems

1k +/-1% 0.1W +/-100ppm/ 0603 Chip Resistor - Surface Mount

USB Hub Controller USB 2.0 USB Interface 36-SQFN (6x6) USB 2.0 Hi-Speed Hub Controller that provides a 2-port USB hub solution supporting USB 2.0 high-speed (480 Mb/s), full-speed, and low-speed operation. It operates from a 3.0 V to 3.6 V supply, supports SMBus/I²C configuration, integrates USB termination and pull-up/pull-down resistors, and is housed in a 36-pin SQFN package. #Microchip #USB2512BTIM2 #USBHubController #USB20 #HiSpeedUSB #TwoPortHub #SMBus #I2C #36SQFN #InterfaceIC

Power Switch/Driver 1:1 P-Channel 2A SOT-23-5 The GLF1100 is an ultra-efficiency, 2 A rated, Load Switch with integrated slew rate control. The best in class efficiency makes it an ideal chose for use in IoT, mobile, and wearable electronics. The GLF1100 features ultra-efficient IQSmartTM technology that supports the lowest quiescent current (IQ) and shutdown current (ISD) in the industry. Low IQ and ISD solutions help designers to reduce parasitic leakage current, improve system efficiency, and increase battery lifetime. The GLF1100 integrated slew rate control can also enhance system reliability by mitigating bus voltage swings during switching events. Where uncontrolled switches can generate high inrush currents that result in voltage droop and/or bus reset events, the GLF slew rate control specifically limits inrush currents during turn-on to minimize voltage droop. GLF1100 Load Switch devices support an industry leading wide input voltage range and helps to improve operating life and system robustness. Furthermore, one device can be used in multiple voltage rail applications which helps to simplify inventory management and reduce operating cost. FEATURES • Wide Input Range: 1.1 V to 5.5 V 6 V abs max • RON : 82 mΩ Typ @ 5.5 VIN • IOUT Max: 2 A • Ultra-Low IQ: 10 nA Typ @ 5.5 VIN • Ultra-Low ISD: 25 nA Typ @ 5.5 VIN • Controlled Rise Time: 2.2 ms at 3.3 VIN • Internal EN Pull-Down Resistor • Integrated Output Discharge Switch • Wide Operating Temperature Range: -40 °C ~ 85 °C • HBM: 6 kV, CDM: 2 kV APPLICATIONS • Telecommunication Module • Low Power Subsystem • Mobile Devices #commonpartslibrary #integratedcircuit #powermanagement #LoadSwitch #PowerManagement #PMIC #HighSideSwitch #LowPower #BatteryPowered #PortableElectronics #GLFIntegratedPower #SOT23 #PowerDistribution

Battery Power Management IC Multi-Chemistry 14-TSSOP The bq34210-Q1 1-Series Cell System-Side CEDV Fuel Gauge provides fuel gauging and End-of-Service (EOS) Determination for 1-series cell batteries in applications that encounter infrequent discharge, such as eCall systems and uninterruptible power supplies (UPS) for backup during power failures, where batteries may stay connected to a charging power source most of their lifetime until needed. The bq34210-Q1 fuel gauge supports multiple battery chemistries, including Li-Ion, LiFePO4, and NiMH. The gas gauging function uses voltage, current, and temperature data along with Compensated End-ofDischarge (CEDV) technology to provide State-ofCharge (SOC) and State-of-Health (SOH) data. The device's EOS Determination function alerts when battery capability has degraded and is approaching the end of its usable service. Battery fuel gauging with the bq34210-Q1 fuel gauge requires connections only to PACK+ (P+) and PACK– (P–) for a removable battery pack or embedded battery management system. Features 1• Automotive-Qualified AEC-Q100, Grade 3 • 1-Series Cell Battery Fuel Gauge Supports Li-Ion, LiFePO4, and NiMH (3-Cell) Chemistries – Resides on System Board – Powers Directly from the Battery with Integrated LDO – Supports a Low-Value External Sense Resistor (10 mΩ) • Learning Load Enable (LEN) from Host • Ultra-Low Power Consumption in NORMAL (50 µA) and SLEEP (9 µA) Modes • Supports Replacement Batteries • Accurate End-of-Service (EOS) Determination for Batteries in Rarely Discharged Applications • CEDV Gas Gauge for 1-Series Cell Batteries, Providing: – State-of-Charge (SOC) – Time-to-Empty (TTE) – State-of-Health (SOH) • High-Side and Low-Side Current Sensing Options • Internal Temperature Sensor OR External Thermistor • Microcontroller Peripheral Interface Supports: – 400-kHz I 2C™ Serial Interface – Configurable Interrupt (ALERT) for SOC, Battery Levels, Temperature Faults, and Charge/Discharge Status 2 Applications • eCall Systems • Telematics Backup Systems • Uninterruptible Power Supply (UPS) Backup Systems • Emergency Battery Power Modules #BatteryFuelGauge #BatteryManagement #FuelGaugeIC #AutomotiveElectronics #TexasInstruments #LiIonBattery #LiFePO4 #I2C #PowerManagement #AECQ100 #BackupBattery #UPS #EmbeddedSystems