Crystals

XL3EL89CMI-111YLC-12M CRYSTAL-SMD_4P-L2.5-W2.0-BL LCSC Part Number: C22434865 JLCPCB Part Class: Extended Part Manufactured by YXC(扬兴晶振)

I-PEX MHF4 Connector Receptacle, Male Pin 50 Ohms Surface Mount Solder The 20449-001E-03 is an ultra-miniature MHF4 RF coaxial receptacle connector from I-PEX designed for high-frequency wireless applications such as Wi-Fi, Bluetooth, LTE, GNSS, and cellular antenna connections in compact electronic devices. It is a surface-mount RF connector optimized for miniature coaxial cable assemblies and high-density PCB layouts. Key Features Ultra-small MHF4 RF coaxial receptacle Supports frequencies up to 9 GHz Characteristic impedance: 50 Ω Surface-mount (SMT) PCB mounting Snap-on mating mechanism Compact footprint for space-constrained designs Gold-plated center contact for improved conductivity and corrosion resistance Uses: MHF4 compatible RF cables and antenna assemblies High-reliability micro RF interconnect Operating temperature: −40°C to +90°C Rated voltage: 60 V Approximate mating cycle rating: 30 cycles Constructed with: Brass contacts LCP (Liquid Crystal Polymer) dielectric material RoHS compliant Typical Applications Wi-Fi modules LTE/5G modules GNSS/GPS antennas Bluetooth devices IoT devices Embedded wireless systems Compact handheld electronics RF communication modules

ARM Microcontrollers - MCU ARM M4 1024 FLASH 168 Mhz 192kB SRAM 100-LQFP (14x14) Arm® Cortex®-M4 32b MCU+FPU, 210DMIPS, up to 1MB Flash/192+4KB RAM, USB OTG HS/FS, Ethernet, 17 TIMs, 3 ADCs, 15 comm. interfaces & camera • Core: Arm® 32-bit Cortex®-M4 CPU with FPU, Adaptive real-time accelerator (ART Accelerator) allowing 0-wait state execution from Flash memory, frequency up to 168 MHz, memory protection unit, 210 DMIPS/ 1.25 DMIPS/MHz (Dhrystone 2.1), and DSP instructions • Memories – Up to 1 Mbyte of Flash memory – Up to 192+4 Kbytes of SRAM including 64- Kbyte of CCM (core coupled memory) data RAM – 512 bytes of OTP memory – Flexible static memory controller supporting Compact Flash, SRAM, PSRAM, NOR and NAND memories • LCD parallel interface, 8080/6800 modes • Clock, reset and supply management – 1.8 V to 3.6 V application supply and I/Os – POR, PDR, PVD and BOR – 4-to-26 MHz crystal oscillator – Internal 16 MHz factory-trimmed RC (1% accuracy) – 32 kHz oscillator for RTC with calibration – Internal 32 kHz RC with calibration • Low-power operation – Sleep, Stop and Standby modes –VBAT supply for RTC, 20×32 bit backup registers + optional 4 KB backup SRAM • 3×12-bit, 2.4 MSPS A/D converters: up to 24 channels and 7.2 MSPS in triple interleaved mode • 2×12-bit D/A converters • General-purpose DMA: 16-stream DMA controller with FIFOs and burst support • Up to 17 timers: up to twelve 16-bit and two 32- bit timers up to 168 MHz, each with up to 4 IC/OC/PWM or pulse counter and quadrature (incremental) encoder input • Debug mode – Serial wire debug (SWD) & JTAG interfaces – Cortex-M4 Embedded Trace Macrocell™ • Up to 140 I/O ports with interrupt capability – Up to 136 fast I/Os up to 84 MHz – Up to 138 5 V-tolerant I/Os • Up to 15 communication interfaces – Up to 3 × I2C interfaces (SMBus/PMBus) – Up to 4 USARTs/2 UARTs (10.5 Mbit/s, ISO 7816 interface, LIN, IrDA, modem control) – Up to 3 SPIs (42 Mbits/s), 2 with muxed full-duplex I2S to achieve audio class accuracy via internal audio PLL or external clock – 2 × CAN interfaces (2.0B Active) – SDIO interface • Advanced connectivity – USB 2.0 full-speed device/host/OTG controller with on-chip PHY – USB 2.0 high-speed/full-speed device/host/OTG controller with dedicated DMA, on-chip full-speed PHY and ULPI – 10/100 Ethernet MAC with dedicated DMA: supports IEEE 1588v2 hardware, MII/RMII #CommonPartsLibrary #IntegratedCircuit #Microcontroller #STM32F407

ARM® Cortex® M3 STM32F1 Microcontroller IC 32-Bit Single-Core 72MHz 64KB (64K x 8) FLASH Medium-density performance line Arm®-based 32-bit MCU with 64 or 128 KB Flash, USB, CAN, 7 timers, 2 ADCs, 9 com. interfaces Arm® 32-bit Cortex®-M3 CPU core – 72 MHz maximum frequency, 1.25 DMIPS/MHz (Dhrystone 2.1) performance at 0 wait state memory access – Single-cycle multiplication and hardware division • Memories – 64 or 128 Kbytes of Flash memory – 20 Kbytes of SRAM • Clock, reset and supply management – 2.0 to 3.6 V application supply and I/Os – POR, PDR, and programmable voltage detector (PVD) – 4 to 16 MHz crystal oscillator – Internal 8 MHz factory-trimmed RC – Internal 40 kHz RC – PLL for CPU clock – 32 kHz oscillator for RTC with calibration • Low-power – Sleep, Stop and Standby modes – VBAT supply for RTC and backup registers • 2x 12-bit, 1 µs A/D converters (up to 16 channels) – Conversion range: 0 to 3.6 V – Dual-sample and hold capability – Temperature sensor • DMA – 7-channel DMA controller – Peripherals supported: timers, ADC, SPIs, I 2Cs and USARTs • Up to 80 fast I/O ports – 26/37/51/80 I/Os, all mappable on 16 external interrupt vectors and almost all 5 V-tolerant Debug mode: – Serial wire debug (SWD) and JTAG interfaces • Seven timers – Three 16-bit timers, each with up to 4 IC/OC/PWM or pulse counter and quadrature (incremental) encoder input – 16-bit, motor control PWM timer with dead-time generation and emergency stop – Two watchdog timers (independent and window) – SysTick timer 24-bit downcounter • Up to nine communication interfaces – Up to two I2C interfaces (SMBus/PMBus®) – Up to three USARTs (ISO 7816 interface, LIN, IrDA capability, modem control) – Up to two SPIs (18 Mbit/s) – CAN interface (2.0B Active) – USB 2.0 full-speed interface • CRC calculation unit, 96-bit unique ID • Packages are ECOPACK #commonpartslibrary #integratedcircuit #microcontroller #stm32f1

25 MHz ±30ppm Crystal 20pF 50 Ohms 4-SMD, No Lead The FL2500283Z is a 25 MHz surface-mount quartz crystal manufactured by Diodes Incorporated, part of the FL series (SaRonix-eCera™). It is designed for use as a stable clock reference in digital circuits such as microcontrollers, communication modules, and embedded systems. This crystal uses an AT-cut resonator inside a compact 3.2 mm × 2.5 mm (3225) ceramic package, making it suitable for high-density PCB designs and modern electronics. Key Features Standard Frequency 25 MHz fundamental mode crystal Compact SMD Package 3.2 × 2.5 mm (3225), 4-pad configuration Height ~0.68–0.75 mm AT-Cut Quartz Technology Provides good frequency stability and low drift Frequency Stability & Tolerance Typical: ±10 to ±30 ppm Load Capacitance Typically 20 pF Low ESR Around 50–60 Ω, suitable for MCU oscillator circuits Wide Operating Temperature Common range: -20°C to +70°C (some variants up to -40°C to +125°C) Surface-Mount Compatibility Ideal for automated assembly and reflow soldering RoHS / Lead-Free Environmentally compliant design Typical Applications Microcontroller clock (STM32, ESP32, AVR, etc.) Communication modules (Wi-Fi, Ethernet, RF) Embedded systems Consumer electronics Industrial control boards #Crystal #Oscillator #Resonator #SaRonix-eCera™ FL

802.15.4, Bluetooth, WiFi Bluetooth v5.0, Zigbee Transceiver Module 2.4GHz PCB Trace Surface Mount The ESP32-C6-WROOM-1-N8 integrates a 32-bit RISC-V single-core processor running up to 160 MHz, along with 8 MB of embedded SPI flash memory. It supports multiple wireless communication protocols, including: Wi-Fi 6 (802.11ax) in the 2.4 GHz band for improved efficiency and lower latency Bluetooth Low Energy (BLE 5) for short-range communication IEEE 802.15.4 for protocols such as Thread and Zigbee The module features a built-in PCB antenna, RF circuitry, crystal oscillator, and passive components, making it a complete solution that simplifies hardware design. It provides a wide range of GPIO pins and peripheral interfaces such as UART, SPI, I2C, PWM, ADC, and more, enabling flexible integration with sensors and external devices. Designed for low power consumption, it includes multiple power-saving modes, making it suitable for battery-powered applications. Typical Applications Smart home and IoT devices Wireless sensors and control systems Industrial automation Smart lighting and energy management Matter-compatible devices (via Thread support)

50 Position Connector Receptacle, Center Strip Contacts Surface Mount Gold The DF12C(3.0)-50DS-0.5V(81) is a high-density, board-to-board mezzanine connector from Hirose Electric’s DF12 series. It features a 0.5 mm pitch with 50 contacts in a dual-row configuration, designed for compact PCB layouts requiring reliable high-speed and high-signal-count interconnections. This connector is optimized for applications such as embedded systems, industrial electronics, communication devices, and portable equipment where space-saving and robust mating performance are critical. Manufacturer Information Manufacturer: Hirose Electric Co., Ltd. Series: DF12 Part Number: DF12C(3.0)-50DS-0.5V(81) Mechanical Specifications Connector Type: Board-to-Board (Mezzanine) Mounting Type: Surface Mount (SMT) Contact Configuration: Dual Row Number of Positions: 50 Pitch: 0.5 mm Stacking Height: 3.0 mm Mating Style: Receptacle (Socket) Contact Plating: Gold over Nickel Termination Style: Solder (SMT pads) Board Retention: None (standard SMT anchoring) Electrical Specifications Rated Current: 0.5 A per contact (typical) Rated Voltage: 50 V AC/DC Contact Resistance: ≤ 100 mΩ (initial) Insulation Resistance: ≥ 100 MΩ Withstanding Voltage: 250 V AC for 1 minute Material Specifications Insulator Material: LCP (Liquid Crystal Polymer), UL94V-0 rated Contact Material: Copper Alloy Plating: Gold plating on contact area, Tin on solder tails Environmental Specifications Operating Temperature Range: -35°C to +85°C Storage Temperature Range: -10°C to +60°C Humidity: Up to 85% RH (non-condensing) Packaging Information Packaging Type: Tape and Reel Reel Quantity: Typically 1,000–2,000 pcs per reel Applications Embedded systems Industrial control equipment Communication devices Portable electronics High-density PCB interconnections Compliance & Standards RoHS Compliant: Yes Halogen-Free: Yes UL Flammability Rating: UL94V-0 Mating Connector Compatible with DF12 series plug connectors with 3.0 mm stacking height and 0.5 mm pitch #commonpartslibrary #connector

16 MHz ±15ppm Crystal 8pF 60 Ohms 4-SMD, No Lead The CX3225SB16000D0GZJC1, manufactured by Kyocera AVX, is a 16.000 MHz crystal oscillator element designed to provide precise frequency reference for microcontrollers, communication ICs, and digital systems. It belongs to the CX3225SB series, known for compact size and stable frequency performance. Key Characteristics Type: Quartz crystal (passive frequency component) Frequency: 16 MHz Load Capacitance: 8 pF Frequency Stability: ±15 ppm Frequency Tolerance: ±15 ppm Operating Mode: Fundamental ESR (Equivalent Series Resistance): ~60–80 Ω Mechanical Details Package: 4-SMD, no-lead (surface mount) Size: 3.2 mm × 2.5 mm (3225 package) Height: ~0.6 mm (low profile) Operating Conditions Temperature Range: −25°C to +85°C Mounting Type: Surface mount (SMT) Function (Simple Explanation) This component: Generates a stable clock signal (16 MHz) Acts as the timing reference for MCUs, processors, or RF modules Works together with internal oscillator circuits inside ICs Microcontroller clock sources (e.g., ESP32, STM32, AVR) Communication modules Embedded systems Consumer electronics IoT devices #CommonPartsLibrary #Crystal #Oscillator #resonator

Connector Header Through Hole 40 position 0.100" (2.54mm) Raspberry Pi 40 pin header The TSW-120-07-G-D is a through-hole, double-row vertical header manufactured by Samtec. It features 40 total positions (2 rows of 20 pins) with a standard 2.54 mm pitch. This connector is widely used for board-to-board connections, prototyping, and general-purpose signal routing in embedded and electronic systems. It is designed for reliable mechanical and electrical performance with gold-plated contacts for enhanced conductivity and corrosion resistance. Manufacturer Samtec Inc. Manufacturer Part Number TSW-120-07-G-D Product Type Through-Hole Pin Header Number of Positions 40 (2 × 20) Number of Rows 2 Pitch 2.54 mm (0.100") Row Spacing 2.54 mm (0.100") Mounting Type Through Hole Orientation Vertical Contact Material Phosphor Bronze Contact Plating Gold (Au) over Nickel Plating Thickness Typically 10 µin (0.25 µm) Gold Insulator Material Black Liquid Crystal Polymer (LCP) Current Rating Typically 3.0 A per contact (depending on application conditions) Voltage Rating Typically 250 VAC Operating Temperature Range -55°C to +125°C Termination Type Solder Contact Style Square Post Post Length Standard Samtec “-07” tail length (approx. 2.92 mm tail, varies slightly per datasheet) Applications Embedded systems (e.g., Raspberry Pi GPIO headers) Development boards and expansion modules Board-to-board interconnects Prototyping and test setups Compliance RoHS Compliant Lead-Free Notes Compatible with standard 2.54 mm female headers and sockets Commonly used in stacking or mezzanine configurations Available in various plating options and pin lengths under the TSW series #commonpartslibrary #connector