Analog Devices

LVDT Signal Conditioner IC – Converts half-bridge, 4-wire LVDT, and RVDT sensor signals into a unipolar or bipolar DC voltage proportional to position. The Analog Devices AD698AP integrates an excitation oscillator, voltage reference, synchronous demodulation, and ratiometric signal conditioning. It supports 20 Hz to 20 kHz excitation, up to 24 V RMS differential excitation, 0.05% linearity, and ±11 V output. The AD698AP is supplied in a 28-PLCC surface-mount package. #AnalogDevices #AD698AP #LVDT #SignalConditioner #PositionSensor #RVDT #SensorInterface #AnalogIC #Instrumentation

Power Management IC (PMIC) with Battery Charger – Integrated power-management IC for small single-cell lithium-ion battery systems, combining a linear battery charger, smart power selector, two 200 mA buck regulators, and three 100 mA LDO regulators. The Analog Devices MAX14745LEWX-T provides programmable regulator outputs, including 0.8–2.375 V / 0.8–3.95 V buck outputs and 0.8–3.6 V / 0.9–4 V LDO outputs. It supports I²C control, thermistor monitoring, power-on reset, voltage sequencing, and operates from −40°C to +85°C in a 36-bump, 0.4 mm-pitch WLP package. #AnalogDevices #MAX14745 #PMIC #BatteryCharger #LiIon #BuckRegulator #LDO #PowerManagement #I2C #EmbeddedSystems

14-Bit 1 GSPS High-Speed Pipeline Analog-to-Digital Converter (ADC) – High-performance ADC designed for software-defined radios (SDR), radar systems, communications equipment, satellite receivers, instrumentation, signal intelligence, wideband data acquisition, and high-speed embedded processing. The Analog Devices AD9690BCPZ-1000 provides 14-bit resolution with a maximum sampling rate of 1 GSPS, using a differential analog input and JESD204B serial digital output for high-speed connection to an FPGA or other high-performance digital processing device. It supports an approximately 2 GHz full-power analog input bandwidth, programmable differential input termination of 50 Ω, 100 Ω, 200 Ω, or 400 Ω, an integrated voltage reference, differential clock input, and flexible JESD204B lane configurations. At 1 GSPS, typical total power consumption is around 2 W. The device also includes two integrated wideband digital processing paths, including NCO and cascaded half-band filtering, which can reduce the amount of data that needs to be processed downstream. The AD9690BCPZ-1000 uses a 64-lead LFCSP package (9 × 9 mm), operates over −40°C to +85°C, and is listed by DigiKey as active. It is particularly well suited for systems where a high-speed ADC needs to interface directly with an FPGA through JESD204B, such as the AMD Kintex UltraScale+ FPGA you provided earlier.

Power over Ethernet (PoE) Flyback Transformer – Surface-mount flyback transformer optimized for Power over Ethernet (PoE) powered devices, isolated DC-DC converters, industrial Ethernet equipment, IP cameras, wireless access points, IoT gateways, and embedded networking applications. Part of the Würth Elektronik WE-PoE+ Series, it is specifically designed for use with the Analog Devices LT4276 PoE PD controller and supports IEEE 802.3at (PoE+) power conversion. Features 38 µH primary inductance (100 kHz), 37 V to 57 V primary input, 12.5 V auxiliary winding at 30 mA, 1,500 Vrms isolation voltage, and operation over a 250 kHz to 400 kHz switching frequency. Built in a compact surface-mount package (13.46 × 15.00 × 12.70 mm), it is specified for −40°C to +125°C operation, making it ideal for high-efficiency isolated PoE power supplies in demanding industrial and embedded environments. #WurthElektronik #750310742 #WEPoEPlus #PoETransformer #FlybackTransformer #PowerOverEthernet #IEEE8023at #LT4276 #DCDCConverter #IndustrialEthernet #EmbeddedPower #EmbeddedSystems

Configurable Analog Front-End (AFE) Potentiostat for Electrochemical Sensors – Ultra-low-power programmable analog front-end designed for electrochemical gas sensors, toxic gas detection, air quality monitoring, industrial safety systems, wearable health devices, environmental monitoring, and embedded sensing applications. The Texas Instruments LMP91000 integrates a complete potentiostat and transimpedance amplifier (TIA), enabling direct interfacing with 2-electrode galvanic and 3-electrode amperometric chemical sensors. Operates from a 2.7 V to 5.25 V supply while consuming less than 10 µA typical supply current, making it ideal for battery-powered systems. Features a programmable TIA gain (2.75 kΩ to 350 kΩ), programmable load resistor, programmable cell bias, I²C-compatible interface, integrated temperature sensor, sensor diagnostics, and support for sensor currents from 5 µA to 750 µA full scale. Housed in a compact 14-pin WSON (4 × 4 mm) package and specified for operation over a −40°C to +85°C temperature range. #TexasInstruments #LMP91000SDXNOPB #LMP91000 #AnalogFrontEnd #Potentiostat #ElectrochemicalSensor #GasSensor #AirQualityMonitoring #IndustrialSafety #I2C #LowPower #EmbeddedSystems

Adjustable Low-Dropout (LDO) Linear Voltage Regulator – Positive adjustable LDO voltage regulator designed for power supplies, industrial control systems, embedded electronics, consumer devices, communication equipment, and analog circuits. Delivers up to 800 mA output current with an adjustable output voltage range of 1.25 V to 13.8 V using an external resistor divider. Operates from an input voltage up to 15 V with a maximum dropout voltage of 1.2 V at 800 mA, making it suitable for low-dropout linear regulation. Features 1% output voltage accuracy, 75 dB PSRR (120 Hz), 5 mA typical quiescent current, current limiting, and thermal shutdown protection for reliable operation. Designed for surface-mount applications in a TO-252-3 (DPAK) package and operates over a 0°C to +125°C temperature range. #TexasInstruments #LM1117DTADJNOPB #LM1117 #LDO #LinearRegulator #VoltageRegulator #AdjustableRegulator #PowerManagement #DPAK #EmbeddedSystems

24 Bit Analog to Digital Converter 4, 8 Input 4 Sigma-Delta 56-VQFN (7x7) The ADS127L14 (quad) and ADS127L18 (octal) are 24-bit, delta-sigma (ΔΣ), analog-to-digital converters (ADCs) based on the single-channel ADS127L11. The devices provide simultaneous sampling of four or eight channels with data rates up to 512kSPS (wideband filter mode) and 1365kSPS (low-latency filter mode). Features • Simultaneously measure four or eight channels • Wideband filter mode: up to 512kSPS • Low-latency filter mode: up to 1365kSPS • Power-scalable speed modes: – Max speed: 512kSPS • 83mW (ADS127L14) • 165mW (ADS127L18) – High speed: 400kSPS • 64mW (ADS127L14) • 128mW (ADS127L18) – Mid speed: 200kSPS • 37mW (ADS127L14) • 74mW (ADS127L18) – Low speed: 50kSPS • 12mW (ADS127L14) • 24mW (ADS127L18) • AC performance with DC precision: (High-Speed Mode) – Dynamic range at 200kSPS: 112dB (typical) – THD: –118dB (typical) – INL: 1ppm of FSR (typical) – Offset drift: 10nV/°C (typical) – Gain drift: 0.5ppm/°C (typical) • Precharge buffered signal inputs • Programmable by pin setting or SPI • Frame-sync port for output data • Internal or external clock operation • Analog supply voltage: 2.85V to 5.5V 2 Applications • Test and measurement: – Data acquisition (DAQ) – Shock and vibration instruments – Acoustics and dynamic strain gauges • Factory automation and control: – Condition monitoring • Aerospace and defense: – Sonar • Medical: – Electroencephalograms (EEG) • Grid Infrastructure: – Power quality analyzers #ADS127L14IRSHT #TexasInstruments #ADC #DeltaSigmaADC #24BitADC #SimultaneousSampling #DataAcquisition #IndustrialAutomation #MedicalInstrumentation #PowerQuality #PrecisionMeasurement #EmbeddedSystems

ADRV9002BBCZ — Analog Devices dual narrow-band/wideband RF transceiver, 30 MHz to 6.0 GHz, up to 40 MHz Tx/Rx bandwidth, in 12 mm × 12 mm 196-ball CSP_BGA package option BC-196-16.