Switches
A switch is a device that allows electricity to flow through a circuit by completing or interrupting the connection. It is a common component in electrical and electronic systems and is used in a variety of applications, such as controlling the flow of electricity in a circuit, turning devices on and off, and routing electrical signals. One of the primary use cases for switches is to control the flow of electricity in a circuit. This can be done by manually flipping the switch or by using a control mechanism, such as a timer or a sensor. Another common use for switches is to turn devices on and off. This can be done using a switch that is built into the device or by using a separate switch that is connected to the device. In addition to these basic use cases, switches can also be used to route electrical signals. For example, a switch can be used to route a signal from one device to another or to direct a signal to a specific circuit or component. If you're looking for a wide variety of switches for your projects, flux.ai has the world's largest community-driven public library of them. The library includes footprints, symbols, datasheets, and simulation models for a wide range of switches, making it easy to find the right switch for your needs.
TPS62840DLCR
1.8V to 6.5V, 750mA, 60nA IQ step-down converter The TPS62840 is a high-efficiency step-down converter with ultra-low operating quiescent current of typically 60 nA. The device contains special circuitry to achieve just 120 nA IQ in 100% mode to further extend battery life near the end of discharge. The device uses DCS-Control to cleanly power radios and operates with a typical switching frequency of 1.8 MHz. In Power-Save Mode, the device extends the light load efficiency down to a load current range of 1 μA and below. 16 predefined output voltages can be selected by connecting a resistor to pin VSET, making the device flexible for various applications with a minimum amount of external components. The STOP pin of the device immediately eliminates any switching noise in order to take a noise-free measurement in test and measurement systems. The TPS62840 provides an output current of up to 750 mA. With an input voltage of 1.8 V to 6.5 V, the device supports multiple power sources such as 2S to 4S Alkaline, 1S to 2S Li-MnO2 , or 1S Li-Ion/LiSOCl2 • 60-nA operating quiescent current • 100% duty-cycle mode with 120-nA IQ • Input voltage range VIN from 1.8 V to 6.5 V • Output current up to 750 mA • RF friendly DCS-Control™ • 80% efficiency at 1 µA IOUT (3.6 VIN to 1.8 VOUT) • 16 selectable output voltages via VSET pin • Auto transition PFM/PWM or forced-PWM mode • Selectable forced PWM and STOP modes • Output discharge function • 25-nA shutdown current • SON-8, WCSP-6 and thermally enhanced HVSSOP-8 packages #CommonPartsLibrary #IntegratedCircuit #PowerManagement
313 Uses0 StarsMOV-14D471K
VARISTOR 470V 4.5kA P=7.5mm The MOV-14D471K is a 14 mm radial leaded metal-oxide varistor designed to protect electronic circuits from sudden voltage spikes such as lightning surges, switching transients, and power-line disturbances. It works by clamping high voltage surges and safely absorbing surge energy, preventing damage to sensitive components downstream. It is commonly placed across L–N (line to neutral) in AC input stages of power supplies and appliances. ⚙️ Key Features Varistor voltage: ~470 V (at 1 mA reference current) Maximum AC operating voltage: 300 VAC Maximum DC voltage: 385 VDC Surge current capability: up to 4.5 kA (8/20 µs pulse) Energy absorption rating: ~125 J Clamping voltage: ~775 V (at rated surge current) Capacitance: ~430 pF Response time: very fast (< nanoseconds range, typical MOV behavior) Operating temperature: -40°C to +85°C (typical range)
263 Uses0 StarsAO3400
The YFW AO3400 is a 30V N-Channel Enhancement MOSFET designed for low-voltage and high-speed switching applications. It uses advanced trench MOSFET technology to achieve low on-resistance (RDS(on)), fast switching performance, and efficient power handling in a compact SOT-23 package. It is commonly used in load switching, DC-DC converters, battery-powered devices, motor control, LED driving, and PWM switching circuits. Key Features N-Channel Enhancement Mode MOSFET Drain-Source Voltage (VDS): 30V Continuous Drain Current (ID): up to 5.8A Low RDS(on): < 28mΩ @ VGS = 10V < 33mΩ @ VGS = 4.5V < 52mΩ @ VGS = 2.5V Logic-Level Gate Drive Compatible Fast Switching Speed Low Gate Charge Compact SOT-23 Package Suitable for PWM and Load Switch Applications RoHS / Pb-Free Compatible Typical Applications Power switching DC-DC converters Battery management systems Motor and fan control LED drivers Portable electronics Microcontroller-based switching circuits #CommonPartsLibrary #Transistor #FET #Mosfet
1.0k Uses0 StarsBQ25750RRVR
Charger IC Multi-Chemistry 36-VQFN (5x6) The BQ25750RRVR is a highly integrated switch-mode battery charge controller and power-path management device designed for single-cell to multi-cell lithium-ion and lithium-polymer battery-powered systems. The device supports bidirectional power conversion, enabling both battery charging and system power delivery through USB Type-C and other DC power sources. It integrates high-efficiency buck-boost charging architecture to maintain optimal charging performance across a wide input voltage range. The device is intended for portable electronics, industrial handheld equipment, USB Power Delivery applications, embedded systems, and battery-powered computing platforms requiring advanced power management and flexible charging capability. Integrated power-path management allows simultaneous system operation and battery charging while maintaining battery protection and system stability. The BQ25750RRVR supports programmable charging parameters through an I2C interface, including charge voltage, charge current, input current limit, and system power regulation. The device includes comprehensive protection functions such as overvoltage protection, overcurrent protection, thermal regulation, battery temperature monitoring, and fault reporting. High switching frequency operation enables reduced external component size and compact PCB implementation. Features Integrated synchronous buck-boost battery charger Supports USB Power Delivery and wide DC input sources Bidirectional power conversion capability I2C programmable charging and system parameters Integrated power-path management High-efficiency charging operation Supports multi-cell lithium-ion and lithium-polymer batteries Programmable input current and charge current limits Dynamic power management and system voltage regulation Integrated ADC monitoring for voltage, current, and temperature Battery supplement mode during adapter removal OTG boost mode support Thermal regulation and thermal shutdown protection Input overvoltage and overcurrent protection Battery overvoltage protection Safety timer and watchdog timer support NTC thermistor interface for battery temperature monitoring Interrupt and fault status reporting Compact WQFN package suitable for space-constrained designs Electrical Characteristics Wide input operating voltage range Programmable battery charge voltage High charge current capability Integrated low RDS(on) MOSFET drivers High switching frequency operation High conversion efficiency across operating range Low standby and shutdown current consumption Accurate input and charge current regulation Integrated analog-to-digital converter telemetry Interface and Control I2C serial communication interface Programmable charging profiles Configurable protection thresholds Status and interrupt reporting ADC telemetry reporting Enable and control pins for system integration Protection Features Input overvoltage protection Input overcurrent protection Battery overvoltage protection Thermal shutdown protection Thermal regulation control Short-circuit protection Watchdog timer protection Safety charging timer Battery temperature qualification support Package Information Package Type: WQFN Package Suffix: RRV Compact thermally enhanced package Surface-mount device Suitable for automated PCB assembly processes Applications USB Type-C charging systems Portable computers and tablets Industrial handheld devices Power banks and battery packs Embedded battery-powered systems Portable instrumentation Consumer electronics Smart battery charging platforms #commonpartslibrary #integratedcircuit #powermanagement #batterycharger
22 Uses0 StarsBQ25622RYKR
Charger IC Lithium Ion/Polymer 18-WQFN-HR (3x2.5) The BQ25622RYKR is a highly integrated standalone switch-mode battery charge management and system power-path management device designed for single-cell lithium-ion and lithium-polymer batteries. The device integrates a high-efficiency synchronous buck charger, system power-path control, input current management, and battery protection functions into a compact solution optimized for portable and embedded applications. The device supports USB and external adapter power sources while providing programmable charging parameters through an I²C interface. Integrated power MOSFETs and advanced power management features reduce external component count and improve overall system efficiency. The charger incorporates dynamic power management, thermal regulation, battery temperature monitoring, and multiple safety protections to ensure reliable operation under varying load and environmental conditions. The BQ25622 family is designed for compact battery-powered systems requiring efficient charging, intelligent power-path control, and low system power consumption. Engineering Specification Manufacturer: Texas Instruments Device Type: Single-Cell Li-Ion/Li-Polymer Switching Battery Charger with Integrated Power-Path Management Battery Chemistry Support: Lithium-Ion and Lithium-Polymer Charging Topology: Synchronous Buck Switching Charger Input Power Sources: USB Input and External DC Adapter Support Charge Current Capability: Programmable Fast Charge Current Support Communication Interface: I²C Serial Communication Interface Integrated Power Devices: Internal High-Side and Low-Side MOSFETs Charging Features: Precharge Mode Fast Charge Mode Charge Termination Automatic Recharge Programmable Charge Parameters Safety Timer Control Power Management Features: Dynamic Power-Path Management Input Current Optimization Narrow Voltage DC Regulation Input Voltage Regulation System Voltage Regulation Monitoring and Reporting Features: Charge Status Monitoring Fault Status Reporting Battery Temperature Monitoring through NTC Interface Input Source Detection Protection Features: Input Overvoltage Protection Battery Overvoltage Protection Thermal Shutdown Protection Thermal Regulation Input Current Limiting Short-Circuit Protection Safety Timer Protection Package Type: WQFN Package Package Variant: RYK Mounting Type: Surface Mount Typical Applications: Portable Consumer Electronics Embedded Battery-Powered Devices IoT Systems Handheld Industrial Equipment USB-Powered Systems Wearable Electronics Portable Medical Devices #commonpartslibrary #integratedcircuit #powermanagement #batterycharger
5 Uses0 StarsBQ25620RYKR
Charger IC Lithium Ion/Polymer 18-WQFN-HR (3x2.5) The BQ25620RYKR is a highly integrated standalone switch-mode battery charge management and system power-path management device designed for single-cell lithium-ion and lithium-polymer batteries. The device integrates a synchronous buck charger, power-path management, input current optimization, and system regulation functions into a compact package suitable for portable and battery-powered embedded systems. It supports USB and adapter power sources with high-efficiency charging operation and dynamic power management for optimized thermal and power performance. The device includes integrated MOSFETs, charge termination, safety timers, input overvoltage protection, thermal regulation, and battery temperature monitoring. It supports I²C communication for programmable charging parameters, system monitoring, and fault reporting. The integrated narrow-voltage DC architecture improves efficiency while reducing external component count and PCB area. Engineering Specification Manufacturer: Texas Instruments Device Type: Single-Cell Li-Ion/Li-Polymer Switching Battery Charger with Power-Path Management Battery Chemistry Support: Lithium-Ion and Lithium-Polymer Charging Topology: Synchronous Buck Converter Input Supply Support: USB Power and External Adapter Sources Input Voltage Operating Range: Wide Input Voltage Support with Input Overvoltage Protection Charge Current Capability: High Current Fast Charging Support System Power Path: Integrated Dynamic Power-Path Management Communication Interface: I²C Serial Interface Integrated MOSFETs: High-Side and Low-Side Power MOSFETs Included Charging Functions: Preconditioning Charge Fast Charge Charge Termination Recharge Function Safety Timer Control Protection Features: Input Overvoltage Protection Battery Overvoltage Protection Thermal Shutdown Thermal Regulation Charge Safety Timer Input Current Limiting Short-Circuit Protection Battery Monitoring Features: Battery Temperature Monitoring via NTC Charge Status Reporting Fault Status Reporting System Voltage Regulation Power Management Features: Narrow Voltage DC Regulation Dynamic Input Power Management Input Current Optimization Automatic Power Source Detection Package Type: WQFN Package Package Variant: RYK Mounting Type: Surface Mount Application Areas: Portable Electronics Embedded Battery-Powered Systems Handheld Devices USB-Powered Equipment Industrial Portable Devices IoT Systems Consumer Electronics #commonpartslibrary #integratedcircuit #powermanagement #batterycharger
5 Uses0 StarsMAX77961BEFV12+
- Voltage Regulator IC 1 Output 30-FC2QFN (4x4) The MAX77960B/MAX77961B are high-performance wide-input 3A (MAX77960B)/6A (MAX77961B) buckboost chargers with Smart Power Selector™ and operate as a reverse buck converter without an additional inductor, allowing the ICs to power USB on-the-go (OTG) accessories. The devices integrate low-loss power switches and provide high efficiency, low heat, and fast battery charging in a small solution size. The reverse buck has true load disconnect and is protected by an adjustable output current limit. The devices are highly flexible and programmable through I2C configuration or autonomously through resistor configuration. The battery charger includes the Smart Power Selector to accommodate a wide range of battery sizes and system loads. The Smart Power Selector allows the system to start up smoothly when an input source is available even when the battery is deeply discharged (dead battery) or missing. For battery safety/authentication reasons, the ICs can be configured to keep charging disabled, and allow the DC-DC to switch and regulate the SYS voltage. The system processor can later enable charging using I2C commands as appropriate. Alternatively, the ICs can be configured to automatically start charging. #CommonPartsLibrary #IntegratedCircuit #PowerManagement #MAX77961
0 Uses0 StarsMAX77962EWJ12+T
Charger IC Lithium Ion 49-WLP (3.46x3.46) The MAX77962 is a high-performance wide-input 3.2A buck-boost charger with a Smart Power Selector™ and operates as a reverse buck without an additional inductor, allowing the IC to power USB On-the-Go (OTG) accessories. The device integrates low-loss power switches, and provides small solution size, high efficiency, low heat, and fast battery charging. The reverse buck has true-load disconnect and is protected by an adjustable output current limit. The device is highly flexible and programmable through I2C configuration or autonomously through resistor configuration. The battery charger includes a Smart Power Selector to accommodate a wide range of battery sizes and system loads. The Smart Power Selector allows the system to start up gracefully when an input source is available even when the battery is deeply discharged (dead battery) or missing. For battery safety/authentication reasons, the IC can be configured to keep charging disabled, and allow the DC-DC to switch and regulate the SYS voltage. The system processor can later enable charging using the appropriate I2C commands. Alternatively, the IC can be configured to automatically start charging. ● 3.5V to 23V Input Operating Range, 30VDC Withstand Voltage ● 97% Peak Efficiency at 9VIN/7.4VOUT/1.5AOUT ● Reverse Leakage Protection ● 50mA to 3.15A Programmable Input Current Limit ● 50mA to 3.2A Programmable Constant Current Charge ● Remote Differential Voltage Sensing ● 600kHz or 1.2MHz Switching Frequency Options ● System Instant On with Smart Power Selector PowerPath ● Charge Safety Timer ● Die Temperature Regulation with Thermal Foldback Loop ● Input Power Management with Adaptive Input Current Limit (AICL) and Input Voltage Regulation ● 10mΩ BATT to SYS Switch, Up to 10A Overcurrent Threshold ● Reverse Buck Mode 5.1V/1.5A to Support USB OTG ● JEITA Compliant with NTC Thermistor Monitor ● I 2C or Resistor Programmable ● 3.458mm x 3.458mm 49-Bump WLP #CommonPartsLibrary #IntegratedCircuit #PowerManagement #MAX77962
0 Uses0 StarsRK806-1
QFN-68(7x7) Power Management - Specialized ROHS The RK806-1 is a multi-channel PMIC designed to deliver and manage power for modern embedded platforms. It integrates multiple high-efficiency DC-DC buck converters, LDO regulators, and a configurable power sequencing controller in a compact QFN-68 package. It is tightly coupled with Rockchip SoCs and is responsible for generating stable voltage rails for CPU cores, GPU, DDR memory, and peripheral blocks. ⭐ Key Features ⚡ 1. High-Integration Power Architecture Multiple synchronous buck converters (high-current rails for CPU/GPU) Several LDO regulators for low-noise analog and IO domains Supports dynamic voltage scaling (DVS) for performance optimization 🔌 2. Wide Output Capability Output voltage range: ~0.5 V to 3.4 V per channel Designed for modern low-voltage SoC power domains Supports both high-current and low-noise power rails 🧠 3. Programmable Power Sequencing OTP / register-configurable power-up & power-down sequence Ensures safe startup for multi-rail SoCs Supports synchronized sequencing with multiple PMICs 📡 4. Digital Control Interface I²C and SPI interface for configuration and control Real-time voltage adjustment per processor demand Register-based control for power modes and telemetry 🛡️ 5. Protection & Reliability Features Over-voltage protection (OVP) Over-current protection (OCP) Thermal shutdown protection Soft-start for inrush current control ⚙️ 6. Efficiency & Performance Optimizations High-frequency switching (~MHz range) for smaller external components Fast transient response for CPU load changes Low standby current for power-sensitive designs 📦 7. Package & Integration QFN-68 (7×7 mm) compact package High thermal efficiency for dense PCB layouts Minimal external components required 📌 Typical Applications Single-board computers (SBCs) AI edge computing devices Tablets and industrial embedded systems Consumer electronics using Rockchip SoCs (e.g., RK3588 platforms) #commonpartslibrary #integratedcircuit #powermanagement
38 Uses0 Stars
