Interface ICs
An interface IC is a type of integrated circuit that is designed to facilitate communication between two devices or systems. These devices are commonly used in electronic systems to enable the transfer of data and control signals between different components or subsystems. Some common use cases for interface ICs include connecting microcontrollers to peripherals such as sensors or displays, linking multiple processors together in a network, and enabling communication between devices using different communication protocols. Flux.ai has the world's largest community-driven public library of interface ICs, with footprints, symbols, datasheets, and simulation models. This library is a valuable resource for engineers and designers who need access to accurate and up-to-date information on these important components. Whether you are working on a new design project or simply looking to learn more about interface ICs, Flux.ai is an excellent resource to help you find the information you need.
LE910C1-AP
Telit LE910C1-AP LTE Cat 1 cellular module for APAC/ANZ/Japan applications. The module uses Telit's 28.2 mm x 28.2 mm x 2.2 mm xE910 181-pad LGA form factor, operates from a 3.4 V to 4.2 V main supply with 3.8 V nominal VBATT, and is rated for -40 C to +85 C industrial operation. LE910C1-AP supports LTE Cat 1 data rates up to 10 Mbps downlink and 5 Mbps uplink; extracted AP variant band data lists FDD LTE B1/B3/B5/B8/B28 with HSPA+ B1/B5/B8 fallback. Key interfaces include USB 2.0 HS/HSIC, UART, SPI/AUX UART, SD/MMC, Wi-Fi SDIO/coexistence, SIM1/SIM2, DVI, GPIO, ADC, I2C, SGMII, main/diversity RF antenna pads, and optional GNSS-related pins where supported. RF pins require 50 ohm controlled-impedance routing; reserved pins should be left floating unless Telit documentation states otherwise.
0 Uses0 StarsAT24C02C-SSHM-T
Serial EEPROM providing 2 Kbit (256 × 8) nonvolatile memory with an I²C-compatible two-wire interface for data storage and system configuration. It operates from 1.7 V to 5.5 V, supports Standard (100 kHz), Fast (400 kHz), and Fast-mode Plus (1 MHz) I²C communication, features 16-byte page write, and is housed in an 8-pin SOIC package. #SerialEEPROM #EEPROM #I2C #NonvolatileMemory #2Kbit #Microchip #SOIC8 #EmbeddedSystems
2 Uses0 StarsTPD4S201RUKR
Overvoltage/Surge Protection IC Internal Switch 20-WQFN (3x3) ESD protection and USB charging-port interface IC for USB 2.0 data lines, integrating IEC 61000-4-2 ±15 kV air and ±8 kV contact ESD protection with support for USB Battery Charging Specification Rev. 1.2 charger detection. It operates from a 2.5 V to 5.5 V supply, includes an integrated high-side VBUS switch rated for up to 1.5 A, and is housed in a 6-pin WQFN (RUK) package. #ESDProtection #USB2_0 #USBCharging #BC1_2 #VBUSSwitch #InterfaceIC #TexasInstruments #WQFN6
7 Uses0 StarsNRF9160-SICA-B1A-R
Cellular IoT System-in-Package (SiP) integrating an Arm Cortex-M33 processor, LTE-M/NB-IoT modem, GNSS receiver, 1 MB Flash, 256 KB RAM, and an integrated power management system. It operates from a 3.0 V to 5.5 V supply, supports GPS, GLONASS, Galileo, and QZSS, and provides interfaces including UART, SPI, I²C, I²S, PWM, ADC, GPIO, and USB 2.0 in a compact SiP package. #CellularIoT #SiP #LTE_M #NB_IoT #GNSS #ArmCortexM33 #NordicSemiconductor #EmbeddedProcessor #LowPower #USB2_0 #UART #SPI #I2C
6 Uses0 StarsWQP-WQP518MA
Audio Connector, designed to provide an interface for audio signal connection in electronic devices. The QingPu WQP-WQP518MA is a compact audio jack connector used for PCB-mounted audio applications. #AudioConnector #AudioJack #Connector #PCBConnector #ElectronicComponent#CommonPartsLibrary #Jack #Audio #Connector
16 Uses0 StarsSLG46826V
Programmable Mixed-Signal Matrix IC – Mixed-signal configurable IC with multiple-time programmable (MTP) non-volatile memory for implementing custom analog and digital functions. Operates from a 2.3 V to 5.5 V supply (VDD) with a secondary 1.71 V to 5.5 V supply (VDD2), and integrates 17 GPIOs, 4 analog comparators, 19 LUTs, 17 D-type flip-flops, 8 counter/delay blocks, 1 pattern generator, 16-stage pipe delay, temperature sensor, RC, low-frequency, and ring oscillators, and an I²C interface. Supports in-system programmability and is housed in a 20-pin STQFN (2 × 3 mm) package. #Renesas #SLG46826V #GreenPAK #ProgrammableMixedSignalIC #ConfigurableLogic #MixedSignal #MTP #I2C #GPIO #AnalogComparator #LUT #ProgrammableLogic #STQFN20 #EmbeddedSystems
0 Uses0 StarsMCP2518FDT-E/QBB
CAN Controller CAN 2.0 SPI Interface 14-VDFN (4.5x3) External CAN FD Controller for adding CAN FD and Classical CAN connectivity to a host MCU via an SPI interface. Supports CAN FD data rates up to 8 Mbps, SPI clock up to 20 MHz, operates from a 2.7 V to 5.5 V supply, and integrates 2 KB message RAM, 31 FIFOs, transmit queue, acceptance filters, and timestamping. #ExternalCANController #CANFD #ClassicalCAN #SPI #8Mbps #20MHzSPI #2.7Vto5.5V #Microchip
30 Uses0 StarsMCP2562FD-H/MF
1/1 Transceiver CANbus 8-DFN (3x3) High-speed CAN FD transceiver for interfacing a CAN protocol controller with a physical CAN bus, supporting CAN FD data rates up to 8 Mbps. Operates from a 4.5 V to 5.5 V supply, features VIO pin for 1.8 V, 2.5 V, 3.3 V, or 5.0 V controller interfaces, supports ISO 11898-2:2016 compliant high-speed CAN, and includes TXD dominant timeout, thermal shutdown, and bus fault protection. #HighSpeedCANFDTransceiver #CANFD #CANBus #8Mbps #ISO118982 #5V #VIOInterface #Automotive #Microchip
9 Uses0 StarsAPS256XXN-OB9-BG
Pseudo Static RAM (PSRAM) – 256 Mbit (32 MB) Octal SPI/Xccela PSRAM organized as 32M × 8 or 16M × 16, supporting Octal Peripheral Interface (OPI) and HyperBus™ Interface (HPI) with DDR operation. Operates from a 1.62 V to 1.98 V supply, supports clock frequencies up to 200 MHz with up to 400 MB/s read/write throughput, and features byte-addressable memory, Data Strobe (DQS), Data Mask (DM), programmable output drive strength, and software reset. Specified for an operating temperature range of −40°C to +85°C and housed in a 24-ball mini-BGA (6 × 8 mm) package. #APMemory #APS256XXNOB9BG #PSRAM #PseudoSRAM #OctalSPI #OPI #HyperBus #Xccela #DDR #256Mbit #32MB #1_8V #BGA24 #EmbeddedMemory #EmbeddedSystems
2 Uses0 StarsSTM32G0B1KEU6
Microcontroller – 32-bit Arm® Cortex®-M0+ microcontroller operating at up to 64 MHz, featuring 512 KB Flash memory, 144 KB SRAM, and 30 programmable I/O pins. Operates from a 1.7 V to 3.6 V supply and integrates a 13-channel 12-bit ADC, 2-channel 12-bit DAC, three analog comparators, and communication interfaces including CAN FD, USB 2.0 Full-Speed, USB Type-C® Power Delivery, I²C, SPI, I²S, UART/USART, HDMI-CEC, IrDA, and LIN. Includes DMA, PWM timers, brown-out detect/reset, power-on reset (POR), and watchdog timer (WDT) peripherals. Housed in a 32-pin UFQFPN (5 × 5 mm) package. #STMicroelectronics #STM32 #STM32G0B1KEU6 #Microcontroller #ARMCortexM0Plus #32BitMCU #64MHz #512KBFlash #144KBSRAM #ADC #DAC #CANFD #USB2 #USBTypeC #I2C #SPI #I2S #UART #UFQFPN32 #EmbeddedSystems
12 Uses0 Stars
