Voltage Regulators
A voltage regulator is an electronic device that maintains a constant output voltage level, regardless of changes in the input voltage or load conditions. These devices are commonly used to provide a stable power supply to electronic circuits, as well as to protect them from voltage spikes and surges. There are several types of voltage regulators, including linear, switching, and pulse width modulation (PWM) regulators, each with its own set of characteristics and applications. Linear regulators, for example, are simple and efficient, but have a relatively low switching speed and can only provide a limited output current. Switching regulators, on the other hand, have higher switching speeds and can provide a higher output current, but are more complex and require additional components. In addition to their use in power supplies and voltage protection, voltage regulators are also used in a wide range of other applications, including motor control, battery charging, and instrumentation. Flux.ai has the world's largest community-driven public library of voltage regulators, with footprints, symbols, datasheets, and simulation models for a wide range of devices. Whether you're a designer, engineer, or hobbyist, you can find the resources you need to get your project up and running quickly and efficiently.
CP2102N-A02-GQFN24
USB-to-UART Bridge CP2102N-A02-GQFN24 is a highly integrated USB-to-UART bridge controller from Silicon Labs. It provides a simple and cost-effective way to add USB connectivity to embedded systems by converting USB 2.0 Full-Speed communication into a standard UART interface. The device integrates the USB transceiver, oscillator, voltage regulator, and UART controller, minimizing external components and eliminating the need for USB firmware development. It is commonly used in microcontroller programming interfaces, industrial equipment, POS terminals, data loggers, and USB-to-serial adapters. Key Features USB 2.0 Full-Speed compliant (12 Mbps) interface. USB-to-UART bridge with data rates up to 3 Mbaud. Integrated USB transceiver; no external USB resistors required. Integrated oscillator; no external crystal required. On-chip 3.3 V voltage regulator. USB Battery Charger Detection (BC 1.2) support. Remote wakeup capability from USB suspend state. Low operating current of approximately 9.5 mA. Hardware and software flow control support. Internal configurable ROM for Vendor ID, Product ID, serial number, and USB descriptors. Royalty-free Virtual COM Port (VCP) drivers available for major operating systems. Operating temperature range: −40°C to +85°C. Compact 24-pin QFN (4 mm × 4 mm) package. Typical Applications USB-to-Serial adapters Microcontroller programming and debugging interfaces Industrial automation equipment Point-of-sale (POS) terminals Medical instruments Data acquisition and logging systems Embedded systems requiring USB connectivity #commonpartslibrary #integratedcircuit
281 Uses0 StarsB0505S-1WR3
The B0505S-1WR3 is a compact isolated DC-DC power converter module designed to provide regulated power conversion while maintaining galvanic isolation between input and output circuits. The module incorporates high-frequency switching technology and transformer isolation to deliver stable power with reduced noise coupling and improved system safety. It is widely used in industrial control systems, communication equipment, instrumentation, data acquisition devices, medical electronics, and embedded applications where isolated power rails are required to eliminate ground loops and enhance signal integrity. Engineering Specification Device Type Isolated DC-DC Converter Module Power Conversion Topology Transformer-Isolated Switching Regulator Input Configuration Single DC Input Output Configuration Single Isolated DC Output Isolation Method Internal High-Frequency Transformer Isolation Regulation Characteristics Regulated Output Voltage High Conversion Efficiency Low Output Ripple and Noise Electrical Features Galvanic Isolation Between Input and Output Enhanced Noise Immunity Stable Load Regulation Reliable Power Transfer Performance Protection Characteristics Short-Circuit Resistant Design Input-to-Output Isolation Protection Thermal Reliability Enhancement Package Style Single In-Line Through-Hole Package Mounting Type Through-Hole Mounting Environmental Characteristics Industrial-Grade Reliability Long Operational Lifetime High Resistance to Electrical Interference Suitable for Harsh Operating Environments Applications Industrial Automation Equipment Data Acquisition Systems Sensor Signal Conditioning Communication Interfaces Medical Electronics Embedded Control Systems Power Supply Isolation Instrumentation Equipment Process Control Devices Microcontroller-Based Systems Features Compact Integrated Module Isolated Power Distribution High Reliability Design Low Electromagnetic Interference Simple Circuit Integration Efficient Power Conversion Stable Output Performance Wide Application Compatibility RoHS Compliant Construction Manufacturer MORNSUN #commonpartslibrary #powermodule #dcdcconverter #isolatedpower #galvanicisolation #powermanagement #powersupply #powerelectronics #industrialelectronics #instrumentation #communications #embeddedsystems #medicalelectronics #throughhole #electroniccomponents
119 Uses0 StarsTPS54336ADRCR
Buck Switching Regulator IC Positive Adjustable 0.8V 1 Output 3A 10-VFDFN Exposed Pad The TPS5433xA family of devices are synchronous converters with an input-voltage range of 4.5 V to 28 V. These devices include This device has an integrated low-side switching FET that eliminates the need for an external diode which reduces component count. Efficiency is maximized through the integrated 128- mΩ and 84-mΩ MOSFETs, low IQ and pulse skipping at light loads. Using the enable pin, the shutdown supply current is reduced to 2 μA. This step-down (buck) converter provides accurate regulation for a variety of loads with a well-regulated voltage reference that is 1.5% over temperature. Cycle-by-cycle current limiting on the high-side MOSFET protects the TPS5433xA family of devices in overload situations and is enhanced by a low-side sourcing current limit which prevents current runaway. A low-side sinking current-limit turns off the low-side MOSFET to prevent excessive reverse current. Hiccup protection is triggered if the overcurrent condition continues for longer than the preset time. Thermal shutdown disables the device when the die temperature exceeds the threshold and enables the device again after the built-in thermal hiccup time. • Synchronous 128-mΩ and 84-mΩ MOSFETs for 3-A Continuous Output Current • TPS54335A: Internal 2-ms Soft-Start, 50-kHz to 1.5-MHz Adjustable Frequency • TPS54336A: Adjustable Soft-Start, Fixed 340-kHz Frequency • Low 2-µA Shutdown, Quiescent Current • 0.8-V Voltage Reference with ±0.8% Accuracy • Current Mode Control • Monotonic Startup into Pre-Biased Outputs • Pulse Skipping for Light-Load Efficiency • Hiccup Mode Overcurrent Protection • Thermal Shutdown (TSD) and Overvoltage Transition Protection • 8-Pin SO PowerPAD™ and 10-Pin VSON Package • Create a Custom Design Using the TPS54335A with the WEBENCH Power Designer #CommonPartsLibrary #IntegratedCircuit #PowerManagement
135 Uses0 StarsLM7812T
Three-Terminal Fixed Positive Voltage Regulator The LM7812T is a three-terminal fixed positive linear voltage regulator IC designed to provide a stable +12V DC output from a higher input voltage source. It belongs to the widely used 78xx series regulators, where “12” indicates the fixed output voltage of 12 volts. It is commonly used in power supply circuits, embedded systems, and electronic devices that require a simple, reliable regulated 12V rail without the complexity of external components. The device operates as a linear regulator, meaning it reduces voltage by dissipating excess energy as heat, so proper heatsinking is often required for higher current loads. Key Features of LM7812T Fixed +12V output voltage Output current up to 1A–1.5A (depending on package and cooling) Input voltage range up to ~35V max Built-in thermal shutdown protection Internal current limiting and short-circuit protection Safe-area compensation for reliable operation No external components required for basic operation Good line and load regulation Low quiescent current (~8 mA typical) Available in TO-220 / TO-3 packages (LM7812T variants) Typical Applications DC power supplies (12V regulated rail) Arduino and microcontroller systems Industrial control electronics Sensor and communication circuits Battery-powered systems requiring stable 12V Audio amplifiers and small motor control circuits #CommonPartsLibrary #IntegratedCircuit #PowerManagement
96 Uses0 StarsTPS25940LRVCR
Electronic Fuse Regulator 5.3A 20-WQFN (3x4) The TPS25940 is a compact, feature-rich eFuse (electronic fuse) power switch from Texas Instruments designed to provide advanced power-path protection and management for SSDs, storage systems, servers, telecom equipment, and other DC-powered applications. It integrates back-to-back MOSFETs for true reverse-current blocking, programmable current limiting, overvoltage/undervoltage protection, and controlled output slew-rate management in a small 20-pin WQFN package. Key Features Wide operating voltage range: 2.7 V to 18 V (20 V maximum input) Low 42 mΩ typical on-resistance (RDS(on)) Adjustable current limit from 0.6 A to 5.3 A True reverse-current blocking using integrated back-to-back FETs Fast reverse-voltage shutdown response of 1 µs Programmable output ramp-up (dV/dt control) for inrush-current management Programmable overvoltage (OVP) and undervoltage (UVP) protection thresholds Integrated IMON analog current-monitor output PGOOD and FLT status outputs for system monitoring Low-power DevSleep™ mode for SATA SSD applications Typical operating quiescent current of 200 µA Typical disabled current of 15 µA Operating junction temperature range from −40°C to +125°C UL 2367 recognized and designed for fault-safe operation under single-point failure conditions. Typical Applications PCIe, SATA, and SAS SSD/HDD storage devices Enterprise servers and storage systems RAID controller cards with holdup-power management Telecom switches and routers Set-top boxes, DTVs, and gaming consoles Adapter-powered equipment General-purpose smart load-switch and power-protection circuits. Package Information Package: 20-pin WQFN (RVC) Temperature range: −40°C to +85°C ambient operation Tape-and-reel packaging for automated assembly. #CommonPartsLibrary #IntegratedCircuit # TPS25940
124 Uses0 StarsTPS62162DSGT
Buck Switching Regulator IC Positive Fixed 3.3V 1 Output 1A 8-WFDFN Exposed Pad The TPS6216x device family are easy to use synchronous step-down DC/DC converters optimized for applications with high power density. A high switching frequency of typically 2.25 MHz allows the use of small inductors and provides fast transient response as well as high output voltage accuracy by utilization of the DCS-Control™ topology. With its wide operating input voltage range of 3 V to 17 V, the devices are ideally suited for systems powered from either a Li-Ion or other battery as well as from 12-V intermediate power rails. It supports up to 1-A continuous output current at output voltages between 0.9 V and 6 V (with 100% duty cycle mode). Power sequencing is also possible by configuring the enable and open-drain power good pins. In power save mode, the devices show quiescent current of about 17 μA from VIN. Power save mode, entered automatically and seamlessly if the load is small, maintains high efficiency over the entire load range. In shutdown mode, the device is turned off and shutdown current consumption is less than 2 μA. The device, available in adjustable and fixed output voltage versions, is packaged in an 8-pin WSON package measuring 2.00 mm × 2.00 mm (DSG) or 8- pin VSSOP package measuring 3.00 mm x 3.00 mm (DGK). • DCS-Control™ Topology • Input Voltage Range from 3 V to 17 V • Up to 1-A Output Current • Adjustable Output Voltage From 0.9 V to 6 V • Fixed Output Voltage Versions • Seamless Power Save Mode Transition • Typically 17-µA Quiescent Current • Power Good Output • 100% Duty Cycle Mode • Short Circuit Protection • Over Temperature Protection • Pin to Pin Compatible With TPS62170 and TPS62125 • Available in 3.00 mm x 3.00 mm 8-Pin VSSOP and 2.00 mm × 2.00 mm 8-Pin WSON Packages • Create a Custom Design using the TPS62160 with the WEBENCH® Power Designer #CommonPartsLibrary #IntegratedCircuit #PowerManagement
290 Uses0 StarsTPS63020DSJT
Buck-Boost Switching Regulator IC Positive Adjustable 1.2V 1 Output 3.5A (Switch) 14-VFDFN Exposed Pad The TPS63020DSJT is a high-efficiency synchronous buck-boost DC-to-DC converter manufactured by Texas Instruments. This integrated power management device is designed to provide a stable regulated output voltage from input power sources that may vary above or below the desired output level. The converter automatically transitions between buck and boost operating modes to maintain efficient and continuous voltage regulation across a wide input range. The device integrates low-resistance power MOSFETs, advanced control circuitry, and high-efficiency switching architecture to minimize power loss and optimize battery utilization in portable electronic systems. It is widely used in battery-powered applications, embedded systems, wireless communication devices, portable instrumentation, industrial electronics, and USB-powered hardware requiring compact and reliable voltage regulation. The TPS63020DSJT is optimized for systems powered by single-cell lithium-ion, lithium-polymer, or multi-cell alkaline battery configurations. Its compact package and integrated functionality reduce external component count and simplify PCB layout while delivering high power conversion efficiency and low quiescent current performance. Engineering Specification Device Type Synchronous buck-boost DC-to-DC converter Power Conversion Topology Automatic buck and boost regulation architecture Input Characteristics Supports input voltages above or below regulated output voltage Output Characteristics Stable regulated DC voltage output Switching Technology Integrated synchronous MOSFET switching architecture Efficiency Characteristics High-efficiency power conversion for battery-powered systems Control Features Automatic operating mode transition and load regulation Power Consumption Low quiescent current operation for portable electronics Thermal Characteristics Integrated thermal management and protection features Protection Features Overcurrent protection Thermal shutdown Undervoltage lockout Short-circuit protection Package Type WSON surface-mount package Mounting Style Surface mount technology Applications Portable electronics Battery-powered systems Embedded hardware Wireless communication devices USB-powered electronics Industrial control systems Portable instrumentation IoT devices Consumer electronics Power management systems Manufacturer Texas Instruments #commonpartslibrary #buckboostconverter #dcdcconverter #powermanagement #texasinstruments #powerelectronics #powersupply #embeddedhardware #portableelectronics #batterypowered #surfaceountcomponents #electronicsdesign #voltageregulator #iothardware #industrialelectronics
118 Uses0 StarsTPAP2112K-3.3TRG1
The TPAP2112K-3.3TRG1 is a low-dropout linear voltage regulator designed to provide a stable regulated output voltage for low-power electronic systems. This device is optimized for applications requiring low noise, low quiescent current, and compact PCB implementation in portable and embedded electronics. The regulator delivers reliable voltage regulation with minimal external component requirements, making it suitable for battery-powered devices, microcontroller systems, wireless modules, sensor interfaces, and general-purpose analog and digital power rails. Its low-dropout architecture enables efficient operation even when the input voltage is close to the regulated output voltage, helping extend battery life in portable applications. The TPAP2112K-3.3TRG1 integrates internal protection features such as current limiting and thermal shutdown to improve system reliability and protect downstream circuitry from abnormal operating conditions. Its compact surface-mount package supports high-density PCB layouts and automated manufacturing processes. Engineering Specification Device Type Low-dropout linear voltage regulator Regulator Topology Positive fixed-output LDO regulator Output Voltage Fixed regulated voltage output Input Characteristics Designed for low-voltage DC input operation Dropout Characteristics Low-dropout voltage architecture for efficient regulation Output Performance Stable low-noise voltage regulation Quiescent Current Low standby current suitable for portable systems Protection Features Current limiting Thermal shutdown Short-circuit protection Thermal Characteristics Efficient thermal operation for compact embedded systems Stability Characteristics Stable operation with standard external capacitors Package Type Surface-mount package Mounting Style Surface mount technology Applications Embedded systems Battery-powered devices Wireless modules Sensor power rails Microcontroller systems Portable electronics IoT hardware Consumer electronics Industrial control systems Analog signal conditioning Manufacturer Commonly associated with 3PEAK or compatible power management vendors #commonpartslibrary #ldoregulator #voltageregulator #powermanagement #powersupply #embeddedhardware #powerelectronics #surfaceountcomponents #electronicsdesign #portableelectronics #iothardware #analogdesign #batterypowered #industrialelectronics #lowpowerelectronics
34 Uses0 StarsTPS63070RNMT
Buck-Boost Switching Regulator IC Positive Adjustable 2.5V 1 Output 2A 15-PowerVFQFN The TPS63070RNMT is a high-efficiency buck-boost DC-to-DC converter manufactured by Texas Instruments. This power management integrated circuit is designed to provide a stable regulated output voltage from input sources that may be above, below, or equal to the desired output voltage. The device automatically transitions between buck and boost operating modes to maintain efficient and continuous power delivery across varying supply conditions. The converter integrates low-resistance power MOSFETs and advanced control circuitry to achieve high conversion efficiency, low quiescent current, and compact implementation. It is widely used in battery-powered systems, portable electronics, embedded devices, industrial control systems, wireless communication equipment, and USB-powered applications requiring stable voltage regulation from fluctuating power sources. The TPS63070RNMT is optimized for applications demanding high power density, extended battery life, and reliable operation under dynamic load conditions. Its compact package and integrated functionality reduce external component count and simplify PCB design for modern power management architectures. Engineering Specification Device Type Synchronous buck-boost DC-to-DC converter Power Topology Automatic buck and boost mode operation Input Voltage Characteristics Supports input voltages above, below, or equal to output voltage Output Characteristics Regulated fixed or adjustable DC voltage output Switching Technology Integrated synchronous power MOSFET architecture Efficiency Characteristics High-efficiency power conversion across wide operating conditions Control Architecture Advanced PWM/PFM power regulation control Current Capability Designed for medium-to-high current portable power applications Quiescent Current Low standby current for battery-powered operation Thermal Characteristics Integrated thermal protection and efficient heat management Protection Features Overcurrent protection Thermal shutdown Undervoltage lockout Short-circuit protection Package Type VQFN surface-mount package Mounting Style Surface mount technology Applications Battery-powered electronics Portable devices USB-powered systems Industrial automation Embedded systems Wireless communication equipment IoT devices Portable instrumentation Power banks Single-cell battery applications Manufacturer Texas Instruments #commonpartslibrary #powermanagement #buckboostconverter #dcdcconverter #texasinstruments #powerelectronics #powersupply #embeddedhardware #portableelectronics #batterymanagement #surfaceountcomponents #electronicsdesign #voltageregulator #industrialelectronics #usbpower
62 Uses0 Stars
