Sensors

Multiprotocol LPWAN 32-bit Arm Cortex-M4 MCUs, LoRa, (G)FSK, (G)MSK, BPSK, up to 256KB flash, 64KB SRAM IC RF TxRx + MCU 802.15.4 LoRa™ 150MHz ~ 960MHz 73-UFBGA The STM32WLE5JCI6 is an ultra-low-power wireless System-on-Chip (SoC) from STMicroelectronics that combines a 32-bit Arm Cortex-M4 microcontroller with an integrated sub-GHz radio transceiver. It is designed for long-range, low-power IoT and LPWAN applications such as smart metering, smart cities, industrial sensors, and remote monitoring systems. It supports multiple modulation schemes including LoRa®, (G)FSK, (G)MSK, and BPSK, making it flexible for both proprietary and standardized wireless protocols like LoRaWAN®. The device integrates RF, analog, digital, and security features into a single chip to reduce external components and PCB size. Key Features Core & Performance 32-bit Arm® Cortex®-M4 core up to 48 MHz DSP instructions and MPU support Up to 256 KB Flash and 64 KB SRAM Wireless Radio Sub-GHz frequency range: 150 MHz – 960 MHz Supports LoRa®, (G)FSK, (G)MSK, BPSK High receiver sensitivity up to –148 dBm (LoRa mode) Output power up to +22 dBm Ultra-Low Power Operation Supply voltage: 1.8 V – 3.6 V Very low sleep currents (nA–µA range) Optimized for battery-powered and energy-harvesting devices Peripherals Up to 43 GPIOs ADC (12-bit), DAC, comparators Multiple timers (16-bit and 32-bit) Interfaces: SPI, I2C, UART/USART, LPUART, I2S Security Features Hardware AES-256 encryption True Random Number Generator (TRNG) Secure memory protection and unique device ID System Integration Integrated RF + MCU (highly reduced BOM) OTA firmware update capability Industrial temperature range (typically –40°C to +85°C / +105°C depending variant) Summary The STM32WLE5JCI6 is a highly integrated LoRa-capable MCU + RF transceiver SoC, optimized for long-range wireless communication with extremely low power consumption, making it ideal for IoT devices that must run for years on battery power. #CommonPartsLibrary #IntegratedCircuit #STM32WLE5JCI6 #STM32WL #LoRa #IoT #LowPowerMCU #ArmCortexM4 #SubGHzRF #WirelessMCU #LPWAN #STMicroelectronics

Texas Instruments OPT4060 high-speed high-sensitivity RGBW color sensor, single-chip light-to-digital sensor with four optical channels for red, green, blue and wide/clear band measurement, I2C interface, semi-logarithmic output with wide dynamic range from 2.15mlux to 144klux, 12 configurable conversion times from 600µs to 800ms, automatic full-scale light range selection, selectable I2C address, interrupt output, low 24µA operating current and 2µA standby current, 1.6V to 3.6V supply range, 5.5V tolerant I/Os, SOT-5X3 2.1 x 1.9 x 0.6mm package. Search Keywords: OPT4060, Texas Instruments OPT4060, TI OPT4060, OPT4060 color sensor, RGBW color sensor, high speed color sensor, high sensitivity color sensor, I2C color sensor, light to digital sensor, RGB light sensor, ambient light color sensor, wide dynamic range light sensor, 144klux sensor, SOT-5X3 color sensor, OPT4060 Hashtags: #OPT4060 #TexasInstrumentsOPT4060 #TIColorSensor #RGBWSensor #ColorSensor #LightSensor #LightToDigitalSensor #I2CSensor #AmbientLightSensor #HighSensitivitySensor #HighSpeedSensor #144kluxSensor #SOT5X3

JLCPCB Part # C70377 QJ.BS-6 battery holder for cylindrical battery cells, through-hole PCB mounting, molded UL94V-0 LCP housing with tin-plated phosphor bronze battery contacts, designed for secure retention and electrical connection of a single cylindrical battery, compact vertical PCB installation, suitable for battery-powered electronic devices, embedded systems, development boards, sensors and portable equipment. Search Keywords: QJ.BS-6, QJ BS-6, battery holder, cylindrical battery holder, PCB battery holder, through hole battery holder, vertical battery holder, battery socket, battery clip holder, UL94V0 battery holder, single cell battery holder, Shenzhen Q&J Electronics battery holder, PCB battery socket #QJBS6 #BatteryHolder #BatterySocket #BatteryClip #PCBBatteryHolder #ThroughHoleBatteryHolder #CylindricalBatteryHolder #SingleCellBatteryHolder #BatteryConnector #PortableElectronics #EmbeddedHardware #PowerSupplyHardware #C70377

TDK T5838 digital PDM MEMS microphone, low-profile surface-mount microphone with pulse density modulation (PDM) output, operating from 1.65V to 1.98V supply, configurable performance modes including High Quality, Low Power and Ultrasonic operation, signal-to-noise ratio (SNR) up to 68dB, acoustic overload point (AOP) up to 133dBSPL, clock frequency range from 400kHz to 4.8MHz, wake-on-sound support, left/right channel selection, compact package optimized for portable audio, voice recognition, smart devices, IoT products and battery-powered applications. Search Keywords: TDK T5838, T5838 MEMS microphone, T5838 PDM microphone, digital MEMS microphone, PDM output microphone, low power MEMS microphone, ultrasonic MEMS microphone, TDK InvenSense microphone, wake on sound microphone, digital microphone 1.8V, MEMS audio sensor, voice recognition microphone, IoT microphone, T5838 datasheet Hashtags: #T5838 #TDKT5838 #TDK #MEMSMicrophone #DigitalMicrophone #PDMMicrophone #AudioSensor #VoiceRecognition #WakeOnSound #LowPowerMicrophone #UltrasonicMicrophone #IoTAudio #SmartDeviceAudio #MEMSAudio #EmbeddedAudio

Infrared (IR) Emitter 940nm 1.2V 100mA 4mW/sr @ 20mA 60° Radial IR7393C Infrared LED Engineering Specification ## General Description The IR7393C is a high-performance infrared emitter designed for sensing, communication, and illumination applications. Manufactured by Everlight Electronics, this LED provides stable infrared output suitable for remote controls, proximity sensors, object detection systems, and other electronic devices requiring infrared illumination. Its compact radial package allows for easy integration into both consumer and industrial electronic assemblies, providing reliable and consistent infrared emission over its operational lifespan. This LED offers robust performance in a wide range of operating conditions, making it suitable for demanding environments. ## Features * Infrared light emission optimized for sensing and communication applications * Standard radial through-hole package for easy PCB integration * High radiant intensity with consistent output * Low power consumption for energy-efficient designs * Reliable performance across temperature variations * Long operational lifetime with stable infrared output * RoHS compliant and environmentally friendly construction * Compatible with automated assembly processes ## Electrical Characteristics * Peak Wavelength: Infrared spectrum suitable for sensing applications * Forward Voltage: Optimized for standard current drive * Forward Current: Continuous operation within rated limits * Reverse Voltage: Safe handling within specified limits * Radiant Intensity: Designed for consistent infrared illumination * Viewing Angle: Moderate beam angle suitable for detection and communication ## Mechanical Characteristics * Package Type: Radial LED * Mounting Style: Through-hole radial leads * Compact design for integration into a variety of electronic devices * Durable epoxy lens for reliable infrared emission ## Applications * Proximity sensors and object detection * Infrared communication systems * Remote control transmitters * Industrial sensing and automation * Consumer electronic devices * IoT devices requiring infrared illumination * Robotic sensors and navigation systems ## Compliance * RoHS Compliant * Lead-free construction * Suitable for automated assembly processes #IR7393C #Everlight #InfraredLED #RadialLED #IREmitter #Sensing #RemoteControl #ProximitySensor #ObjectDetection #ElectronicsDesign #EmbeddedSystems

Supervisor Open Drain or Open Collector 1 Channel 8-SOIC The MC34164D-5R2G is a high-speed, dual operational amplifier designed for precise analog signal processing in industrial, instrumentation, and consumer electronic applications. It features low offset voltage, low input bias current, and wide bandwidth for accurate and reliable performance across various analog signal conditions. Its robust design provides stable operation under high-speed switching and varying temperature conditions, making it suitable for data acquisition systems, sensor interfaces, audio signal conditioning, control circuits, and measurement instrumentation. The device comes in a compact dual-in-line package for easy PCB integration and versatility in mixed-signal designs. Engineering Specifications Manufacturer: ON Semiconductor Part Number: MC34164D-5R2G Device Type: Dual Operational Amplifier Amplifier Configuration: Dual Op-Amp Input Offset Voltage: Low for Precision Applications Input Bias Current: Low Supply Voltage Range: Wide Operating Range Gain Bandwidth Product: High for Fast Signal Processing Slew Rate: Optimized for High-Speed Applications Output Type: Rail-to-Rail Compatible Noise Performance: Low Noise Analog Operation Package Type: Small Outline Integrated Circuit (SOIC) Mounting Style: Surface Mount Operating Temperature Range: Industrial Grade RoHS Compliant: Yes Applications: Sensor Signal Conditioning, Data Acquisition, Control Systems, Audio Processing, Industrial Instrumentation, Embedded Analog Circuits, Measurement and Monitoring Equipment, General-Purpose Analog Designs Key Features Dual high-speed operational amplifier in a single package Low input offset voltage for precision analog applications Low input bias current for high-impedance signal sources Wide supply voltage range for flexible design Fast slew rate and high gain bandwidth for accurate signal processing Compact surface-mount package for space-efficient PCB layouts Stable operation under industrial temperature ranges Suitable for instrumentation and embedded analog signal circuits Low-noise design for high-fidelity analog applications #MC34164D5R2G #ONSemiconductor #OperationalAmplifier #OpAmp #DualOpAmp #HighSpeedOpAmp #AnalogSignalProcessing #SensorInterface #DataAcquisition #ControlSystems #AudioProcessing #IndustrialElectronics #EmbeddedSystems #SOICPackage #SurfaceMount #ElectronicComponents #PCBDesign #PrecisionAmplifier #SignalConditioning

Pressure Sensor 2.9PSI ~ 36.26PSI (20kPa ~ 250kPa) Absolute Male - 0.19" (4.93mm) Tube 0.2 V ~ 4.9 V 6-SIP Module The MPX4250AP is an integrated silicon pressure sensor designed for measuring absolute pressure in automotive, industrial, and embedded control applications. Utilizing advanced piezoresistive sensing technology, the device provides a highly accurate analog voltage output that is directly proportional to the applied pressure. It incorporates on-chip signal conditioning, temperature compensation, and calibration circuitry to deliver stable and reliable performance across varying environmental conditions. The sensor is commonly used in engine management systems, manifold absolute pressure monitoring, altitude measurement, pneumatic controls, weather monitoring equipment, and general-purpose pressure sensing applications requiring precise and repeatable measurements. Engineering Specifications Manufacturer: NXP Semiconductors Part Number: MPX4250AP Device Type: Absolute Pressure Sensor Sensor Technology: Silicon Piezoresistive Pressure Measurement: Absolute Pressure Output Type: Analog Voltage Signal Conditioning: Integrated Temperature Compensation: Integrated Calibration: Factory Calibrated Supply Configuration: Single Supply Operation Response Time: Fast Dynamic Response Accuracy: High Accuracy Pressure Measurement Sensitivity: Optimized for Automotive and Industrial Applications Package Type: Through-Hole Unibody Package Mounting Style: Through-Hole Port Style: Single Pressure Port Operating Temperature Range: Automotive and Industrial Grade RoHS Compliant: Yes Applications: Automotive Engine Control, Manifold Pressure Monitoring, Altitude Measurement, Industrial Automation, Pneumatic Systems, Environmental Monitoring, Embedded Control Systems Key Features Integrated signal conditioning circuitry Temperature-compensated output Factory-calibrated performance High reliability and long-term stability Analog voltage output proportional to pressure Suitable for harsh automotive environments Fast response and accurate pressure sensing Simplified system integration with minimal external components #MPX4250AP #PressureSensor #AbsolutePressureSensor #NXP #PiezoresistiveSensor #AutomotiveElectronics #EngineManagement #MAPSensor #IndustrialAutomation #EmbeddedSystems #AnalogSensor #EnvironmentalMonitoring #ControlSystems #SensorTechnology #ElectronicComponents #PCBDesign #SignalConditioning #PressureMeasurement #AutomotiveSensor #IndustrialElectronics

Standard (General Purpose) Amplifier 4 Circuit Rail-to-Rail 14-TSSOP The ADA4096-4ARUZ-R7 is a precision quad operational amplifier designed for industrial, instrumentation, automotive, and general-purpose signal conditioning applications. It features rail-to-rail input and output operation, allowing accurate signal processing across a wide supply voltage range while maintaining low offset voltage, low bias current, and high stability. The device incorporates overvoltage protection on the inputs, enabling robust performance in harsh operating environments and fault-tolerant designs. Its combination of precision, low power consumption, and wide dynamic range makes it suitable for sensor interfaces, data acquisition systems, process control equipment, battery-powered devices, and measurement instrumentation. Engineering Specifications Manufacturer: Analog Devices Part Number: ADA4096-4ARUZ-R7 Device Type: Precision Operational Amplifier Amplifier Configuration: Quad Input Stage: Rail-to-Rail Output Stage: Rail-to-Rail Supply Voltage Range: Wide Operating Range Input Overvoltage Protection: Integrated Input Bias Current: Low Input Offset Voltage: Low Noise Performance: Low Noise Operation Gain Bandwidth Product: Optimized for Precision Signal Conditioning Slew Rate: Suitable for General-Purpose Analog Applications Power Consumption: Low Power Package Type: Thin Shrink Small Outline Package Mounting Style: Surface Mount Operating Temperature Range: Industrial Grade RoHS Compliant: Yes Applications: Sensor Interfaces, Data Acquisition Systems, Industrial Control, Instrumentation, Medical Electronics, Process Monitoring, Battery-Powered Equipment, Analog Signal Conditioning Key Features Rail-to-rail input and output architecture Input overvoltage protection for enhanced robustness Low offset voltage for precision measurements Low bias current for high-impedance sensor applications Stable operation across a wide supply range Suitable for single-supply and dual-supply designs Optimized for industrial and instrumentation environments #ADA4096 #ADA40964ARUZR7 #AnalogDevices #OperationalAmplifier #OpAmp #PrecisionAmplifier #RailToRail #SignalConditioning #InstrumentationAmplifier #IndustrialElectronics #DataAcquisition #SensorInterface #AnalogDesign #PCBDesign #EmbeddedSystems #SurfaceMount #LowPowerElectronics #ElectronicComponents

Coin, 20.0mm Lithium Manganese Dioxide 3 V Battery Non-Rechargeable (Primary) The CR2032 is a compact, coin-cell lithium battery widely used in portable electronic devices, providing long-lasting, stable power in a small form factor. It features a cylindrical shape with a flat positive terminal and a metal casing that serves as the negative terminal. Known for its high energy density and wide operating temperature range, this battery is ideal for memory backup, real-time clocks, small medical devices, remote controls, wearable electronics, and low-drain consumer electronics. Its reliability, shelf life, and lightweight design make it a standard choice for a broad range of compact electronic applications. Engineering Specifications Battery Type: Lithium Coin Cell Chemistry: Lithium Manganese Dioxide Standard Designation: CR2032 Nominal Voltage: 3 Volts Capacity: Typical Rated Capacity for Consumer Electronics Discharge Characteristics: Suitable for Low-Drain Applications Dimensions: Standard Diameter and Height for CR2032 Operating Temperature Range: Wide Range for Consumer and Industrial Use Shelf Life: Extended, Suitable for Long-Term Storage Terminals: Flat Positive Top, Metal Casing Negative Bottom RoHS Compliant: Yes Applications: Watches, Calculators, Motherboard CMOS Backup, Fitness Trackers, Remote Controls, Medical Devices, Sensors, Small Electronics #CR2032 #LithiumBattery #CoinCell #3Volt #LongLifeBattery #PortableElectronics #Wearables #ConsumerElectronics #MemoryBackup #LowDrainDevice #IndustrialElectronics #BatteryComponent #PCBDesign #CompactPower

Bus Switch 1 x 8:1 24-VQFN (4x4) # TCA9548ARGER Engineering Specifications **General Description** The TCA9548ARGER is a low-voltage I²C and SMBus switch manufactured by Texas Instruments. It is designed to expand and manage I²C communication networks by allowing a single master device to selectively communicate with multiple downstream buses through independent switching channels. The device functions as a bidirectional translating switch, enabling communication between devices operating at different voltage levels while maintaining protocol compatibility. Through software control, individual channels can be enabled or disabled, providing flexible bus segmentation, address conflict resolution, and system scalability. The TCA9548ARGER is widely used in embedded systems, industrial control equipment, data acquisition platforms, telecommunications hardware, server management systems, sensor networks, and Internet of Things applications where multiple I²C devices must be connected to a single controller. Its low-power CMOS architecture, integrated reset functionality, and hot-insertion support make it suitable for complex digital systems requiring reliable and efficient I²C bus management. **Engineering Specifications** **Manufacturer:** Texas Instruments **Manufacturer Part Number:** TCA9548ARGER **Component Type:** I²C bus switch and multiplexer **Technology:** Low-voltage CMOS **Interface Standard:** I²C and SMBus compatible **Switch Configuration:** Multiple downstream I²C channel selection **Channel Operation:** Software-controlled channel enable and disable **Communication Direction:** Bidirectional signal transmission **Voltage Translation Capability:** Supports communication between devices operating at different logic voltages **Bus Isolation Function:** Independent channel isolation for address conflict management **Control Method:** I²C command-based channel selection **Address Selection:** Configurable device addressing through hardware address pins **Power Supply Configuration:** Single-supply operation **Power Consumption:** Low-power operation suitable for embedded applications **Signal Integrity Features:** Low ON-state resistance and low propagation delay **Reset Function:** Dedicated hardware reset input **Hot Insertion Support:** Prevents bus disruption during device insertion and removal **Fail-Safe Characteristics:** Protection against unintended bus communication during power transitions **Bus Capacitance Management:** Improves communication reliability in large I²C networks **System Scalability:** Supports expansion of sensor, peripheral, and control-device networks **Electrostatic Protection:** Integrated ESD protection circuitry **Operating Temperature Range:** Industrial temperature range **Package Type:** VQFN surface-mount package **Mounting Style:** Surface mount technology **Package Construction:** Leadless thermally efficient package **Environmental Compliance:** RoHS compliant and lead-free **Reliability Features:** Designed for high-reliability industrial and embedded applications **Typical Applications** I²C bus expansion systems Sensor aggregation networks Industrial automation equipment Embedded controller platforms Server management systems Data acquisition hardware Telecommunications equipment Internet of Things devices Medical instrumentation Consumer electronics Robotics and automation systems Environmental monitoring devices Smart building control systems Automotive electronic subsystems Multi-sensor embedded applications #TCA9548A #TCA9548ARGER #TexasInstruments #I2C #SMBus #BusMultiplexer #I2CSwitch #EmbeddedSystems #IndustrialAutomation #SensorNetworks #IoT #DataAcquisition #ElectronicsEngineering #ElectronicComponents #EngineeringSpecifications