Sensors

Linear Voltage Regulator IC Positive Fixed 1 Output 500mA SOT-23-5 The TLV75533PDBVR is a low-dropout (LDO) linear voltage regulator designed to provide a stable 3.3 V output from a higher input voltage source. It features ultra-low quiescent current and high power-supply rejection ratio (PSRR), making it ideal for battery-powered and noise-sensitive applications such as IoT devices, portable electronics, and RF circuits. The device is optimized for fast transient response and stable operation with small ceramic output capacitors. Key Features Fixed output voltage: 3.3 V Low dropout voltage (typ. ~200 mV at full load) Ultra-low quiescent current (typ. 25 µA) High PSRR for noise-sensitive applications Stable with small ceramic capacitors (≥1 µF) Thermal shutdown and overcurrent protection Available in compact SOT-23-5 package (DBV) Absolute Maximum Ratings Input voltage: –0.3 V to 6.5 V Output voltage: –0.3 V to (VIN + 0.3 V) Operating junction temperature: –40°C to +125°C Storage temperature range: –65°C to +150°C Recommended Operating Conditions Input voltage range: 1.45 V to 5.5 V Output voltage: 3.3 V (fixed) Output current: up to 500 mA Operating temperature range: –40°C to +125°C Electrical Characteristics (Typical unless otherwise noted) Output voltage accuracy: ±1% Dropout voltage: ~200 mV @ 500 mA Quiescent current: ~25 µA PSRR: up to 70 dB (at 1 kHz) Line regulation: <0.05%/V Load regulation: <0.5% Pin Configuration (SOT-23-5) Pin 1: IN – Input voltage Pin 2: GND – Ground Pin 3: EN – Enable (active high) Pin 4: NC – No connect Pin 5: OUT – Regulated output Typical Application Power management for microcontrollers and sensors Battery-powered portable devices RF and analog circuits requiring low noise supply IoT and wearable electronics Protection Features Thermal shutdown protection Overcurrent protection Undervoltage lockout (UVLO) #commonpartsLibrary #integratedcircuit #powermanagement #voltageregulator

ARM® Cortex® M3 STM32F1 Microcontroller IC 32-Bit Single-Core 72MHz 64KB (64K x 8) FLASH Medium-density performance line Arm®-based 32-bit MCU with 64 or 128 KB Flash, USB, CAN, 7 timers, 2 ADCs, 9 com. interfaces Arm® 32-bit Cortex®-M3 CPU core – 72 MHz maximum frequency, 1.25 DMIPS/MHz (Dhrystone 2.1) performance at 0 wait state memory access – Single-cycle multiplication and hardware division • Memories – 64 or 128 Kbytes of Flash memory – 20 Kbytes of SRAM • Clock, reset and supply management – 2.0 to 3.6 V application supply and I/Os – POR, PDR, and programmable voltage detector (PVD) – 4 to 16 MHz crystal oscillator – Internal 8 MHz factory-trimmed RC – Internal 40 kHz RC – PLL for CPU clock – 32 kHz oscillator for RTC with calibration • Low-power – Sleep, Stop and Standby modes – VBAT supply for RTC and backup registers • 2x 12-bit, 1 µs A/D converters (up to 16 channels) – Conversion range: 0 to 3.6 V – Dual-sample and hold capability – Temperature sensor • DMA – 7-channel DMA controller – Peripherals supported: timers, ADC, SPIs, I 2Cs and USARTs • Up to 80 fast I/O ports – 26/37/51/80 I/Os, all mappable on 16 external interrupt vectors and almost all 5 V-tolerant Debug mode: – Serial wire debug (SWD) and JTAG interfaces • Seven timers – Three 16-bit timers, each with up to 4 IC/OC/PWM or pulse counter and quadrature (incremental) encoder input – 16-bit, motor control PWM timer with dead-time generation and emergency stop – Two watchdog timers (independent and window) – SysTick timer 24-bit downcounter • Up to nine communication interfaces – Up to two I2C interfaces (SMBus/PMBus®) – Up to three USARTs (ISO 7816 interface, LIN, IrDA capability, modem control) – Up to two SPIs (18 Mbit/s) – CAN interface (2.0B Active) – USB 2.0 full-speed interface • CRC calculation unit, 96-bit unique ID • Packages are ECOPACK #commonpartslibrary #integratedcircuit #microcontroller #stm32f1

Linear Voltage Regulator IC Positive Fixed 1 Output 150mA SOT-23-5 LP2985IM5-2.7 is a low-dropout (LDO) linear voltage regulator designed to provide a stable 2.7 V output with very low quiescent current and excellent noise performance. It is optimized for battery-powered and noise-sensitive applications, offering high power supply rejection ratio (PSRR) and fast transient response. The device is housed in a compact SOT-23-5 package, making it ideal for space-constrained designs. Key Features Fixed 2.7 V output voltage Low dropout voltage Low quiescent current (IQ) High PSRR for noise-sensitive applications Stable with low ESR ceramic capacitors Thermal shutdown and current limit protection Small SOT-23-5 package RoHS compliant Electrical Characteristics Output Voltage: 2.7 V (fixed) Output Voltage Accuracy: ±1.5% (typical) Maximum Output Current: 150 mA Dropout Voltage: ~280 mV at 150 mA (typical) Quiescent Current (IQ): ~65 µA (typical) Line Regulation: 0.04%/V (typical) Load Regulation: 0.2% (typical) PSRR: Up to 70 dB (at low frequency) Operating Input Voltage Range: 2.5 V to 16 V Operating Temperature Range: -40°C to +125°C Mechanical Characteristics Package Type: SOT-23-5 (DBV) Mounting Type: Surface Mount Pin Count: 5 pins Approximate Dimensions: 2.9 mm × 1.6 mm Pin Configuration (Typical) IN: Input voltage GND: Ground OUT: Regulated output (2.7 V) EN: Enable (active high) BYPASS: Noise reduction / bypass capacitor connection Performance Characteristics Excellent output noise performance (low-noise design) Fast transient response to load changes Stable with small ceramic capacitors (typically 1 µF) Suitable for RF and analog circuits Applications Battery-powered devices Portable electronics RF and wireless modules Sensors and analog circuits Microcontroller power supplies #CommonPartsLibrary #IntegratedCircuit #PowerManagement #voltage-regulator #LDO #LP3985

Pressure Sensor +/-0.22PSI (+/-1.5kPa) Differential Male - 0.08\" (2.00mm) Tube, Dual 16 b 16-SMD Module, Dual Top Ports The SDP33-1500Pa-TR-250PCS is a digital differential pressure sensor module from Sensirion AG, designed for high-precision measurement of low-pressure differences up to ±1500 Pa (±1.5 kPa). It belongs to the SDP3x series, which uses Sensirion’s CMOSens® technology for compact, accurate, and stable sensing performance. It is widely used in HVAC systems, airflow measurement, medical devices, and industrial control applications where precise air or gas flow monitoring is required. Key Features Differential Pressure Measurement Range: ±1500 Pa (±1.5 kPa) Digital Output Interface I²C communication for easy MCU integration High Resolution 16-bit digital output Accurate & Stable Performance Factory-calibrated and temperature compensated No zero-point drift Low Power Consumption Designed for battery-powered and embedded systems Compact SMD Module Small footprint, surface-mount package (easy PCB integration) Fast Response Time Suitable for real-time airflow and pressure monitoring Wide Operating Conditions Supply voltage: ~3.3V Operating temperature: -40°C to +85°C Reflow Solderable Compatible with standard SMT manufacturing processes Reliable Long-Term Stability Built for high-volume industrial and commercial applications Typical Applications HVAC airflow and filter monitoring Ventilation and air quality systems Medical respiratory devices Industrial automation and process control Drones and airspeed (pitot tube systems) IoT environmental sensing #CommonPartsLibrary #Sensor

Optical Sensor 0.787" ~ 98.425" (20mm ~ 2500mm) Push-Pull Output #OpticalSensor #lazer #part #i2c #spi

Optical Sensor Ambient I2C 8-SMD, No Lead The LTR-559ALS-01 is a combined ambient light sensor and proximity sensor module designed for low-power and space-constrained applications. It integrates a photodiode array for ambient light detection and an infrared emitter with a photodiode for proximity sensing. The device provides digital output via an I²C interface and includes programmable interrupt functionality for system-level event handling. It is commonly used in mobile devices, wearable electronics, and industrial applications requiring automatic brightness control and object detection. Key Features: Integrated ambient light and proximity sensing functions High sensitivity with wide dynamic range for light measurement Infrared LED driver for proximity detection I²C digital interface for communication Programmable interrupt output Low power consumption with multiple operating modes Built-in noise cancellation and sunlight rejection Compact surface-mount package Electrical Characteristics: Supply voltage range: compatible with typical low-voltage logic systems Low standby current for power-sensitive applications Programmable gain and integration time for ambient light sensing Adjustable LED drive current for proximity sensing Optical Characteristics: Ambient light sensing with human-eye spectral response approximation Proximity detection using infrared light with high immunity to ambient light interference Interface: Communication protocol: I²C-compatible interface Supports configurable registers for threshold, timing, and interrupt control Package Information: Small form factor surface-mount package suitable for compact PCB layouts Integrated optical window for both ALS and proximity sensing Applications: Display brightness control in smartphones and tablets Proximity detection for touchless interfaces Wearable devices and IoT sensors Industrial automation and control systems Environmental and Compliance: Designed for standard commercial temperature ranges RoHS compliant and suitable for lead-free assembly processes Notes for Design Integration: Requires proper optical isolation between emitter and receiver for accurate proximity sensing PCB layout should minimize interference from external light sources Calibration may be required depending on enclosure and application conditions #commonpartslibrary #sensor #ambient

IC RF TxRx Only Bluetooth, WiFi Bluetooth v5.0, Thread, Zigbee® 2.412GHz ~ 2.484GHz 32-VFQFN Exposed Pad The ESP32-C6FH4 is a low-power, highly integrated wireless microcontroller from Espressif Systems, designed for IoT applications. It is based on a 32-bit RISC-V processor running at up to 160 MHz, providing efficient performance for embedded systems while maintaining low power consumption. This variant includes 4 MB of embedded flash memory, making it suitable for standalone applications without the need for external flash. The ESP32-C6FH4 supports multiple wireless communication protocols, including: Wi-Fi 6 (802.11ax) in the 2.4 GHz band (backward compatible with Wi-Fi 4/802.11 b/g/n) Bluetooth Low Energy (BLE 5) IEEE 802.15.4 (used for protocols like Thread and Zigbee) Key features include: Rich set of GPIO pins with support for peripherals such as UART, SPI, I2C, PWM, ADC, and more Integrated hardware security features (secure boot, flash encryption, cryptographic accelerators) Multiple low-power modes for battery-operated devices On-chip temperature sensor and RTC peripherals #commonpartslibrary #transceiver

802.15.4, Bluetooth, WiFi Bluetooth v5.0, Zigbee Transceiver Module 2.4GHz PCB Trace Surface Mount The ESP32-C6-WROOM-1-N8 integrates a 32-bit RISC-V single-core processor running up to 160 MHz, along with 8 MB of embedded SPI flash memory. It supports multiple wireless communication protocols, including: Wi-Fi 6 (802.11ax) in the 2.4 GHz band for improved efficiency and lower latency Bluetooth Low Energy (BLE 5) for short-range communication IEEE 802.15.4 for protocols such as Thread and Zigbee The module features a built-in PCB antenna, RF circuitry, crystal oscillator, and passive components, making it a complete solution that simplifies hardware design. It provides a wide range of GPIO pins and peripheral interfaces such as UART, SPI, I2C, PWM, ADC, and more, enabling flexible integration with sensors and external devices. Designed for low power consumption, it includes multiple power-saving modes, making it suitable for battery-powered applications. Typical Applications Smart home and IoT devices Wireless sensors and control systems Industrial automation Smart lighting and energy management Matter-compatible devices (via Thread support)

MCP3913 Series 3.6 V 4.5 mA SMT Six-Channel Analog Front End - SSOP-28 The MCP3913A1T-E/SS is a high-performance, multi-channel analog front-end (AFE) from Microchip Technology intended for precision measurement applications. It features six simultaneous sampling 24-bit delta-sigma ADCs with integrated programmable gain amplifiers, enabling accurate acquisition of low-level analog signals. Designed for energy monitoring and industrial sensing, the device provides low noise, high dynamic range, and flexible configuration. It supports SPI communication for efficient interfacing with microcontrollers and digital processing systems. Key Features Six simultaneous sampling 24-bit delta-sigma ADC channels Integrated programmable gain amplifiers per channel High signal-to-noise ratio and low distortion Programmable oversampling ratios for performance tuning Internal voltage reference with external reference option SPI-compatible digital interface Configurable data output formats and control registers Low power operation modes Electrical Characteristics Resolution: 24-bit Number of Channels: 6 Input Configuration: Differential Supply Voltage: 2.7V to 3.6V Operating Temperature Range: -40°C to +125°C Programmable Gain: Up to 32 V/V (typical) Reference Voltage: Internal or external selectable Functional Description The device integrates six high-resolution delta-sigma ADCs that sample input signals simultaneously, ensuring accurate phase and timing relationships across channels. Each input passes through a programmable gain stage, allowing optimization for different sensor levels. Analog signals are digitized using oversampling and digital filtering techniques to achieve high precision and noise reduction. Configuration is handled via internal registers, and data is transferred through an SPI interface. Package Information Package Type: SSOP Pin Count: 28 Mounting Type: Surface Mount Applications Energy metering Power monitoring systems Industrial automation Multi-channel data acquisition Sensor interfacing Smart grid systems Advantages High integration reduces external components Simultaneous sampling improves measurement accuracy High resolution supports precise signal analysis Flexible configuration for various system requirements #commonpartslibrary #integratedcircuit #powermanagement #energymetering

RF System on a Chip - SoC Cortex-M55 250MHz, 2.5D GPU, 4MB MRAM, 3.75MB SRAM, BLE5.4, -20 to +70 C, BGA , 1.71 V to 2.2 V -20C ~ 70C ARM® Cortex®-M55 System On Chip (SOC) IC Apollo510B 250MHz The AP510BFA-CBR is an ultra-low-power MCU System-on-Chip (SoC) designed for advanced embedded and edge-AI applications. It belongs to the Apollo510B series and integrates a powerful ARM Cortex-M55 processor optimized for both performance and energy efficiency. It combines processing, memory, and multiple peripherals into a single BGA package, making it suitable for compact and power-sensitive designs. Key Characteristics Core: ARM Cortex-M55 Max CPU Speed: 250 MHz Architecture: MCU / SoC Flash Memory: 4 MB RAM: ~3.75 MB Connectivity: I2C, SPI, UART, USB Wireless Support: Bluetooth 5.4 (variant dependent) Package: 153-BGA (compact high-density package) Key Features Built on Ambiq’s ultra-low-power SPOT technology Designed for battery-powered and energy-sensitive devices High computational performance for edge AI and DSP workloads Integrated peripherals for embedded system development Typical Applications Wearables (smartwatches, fitness bands) Smart home and IoT devices Edge AI / machine learning nodes Industrial sensors and monitoring systems Wireless communication modules #CommonPartsLibrary #IntegratedCircuit #SoC #Apollo510B