Microcontrollers

22 Position Receptacle Connector 0.100" (2.54mm) Through Hole Gold The SSW-122-02-G-S is a surface-mount, single-row socket strip designed for reliable board-to-board or component interconnection in electronic assemblies. It is part of a standardized connector series intended for applications requiring compact form factor, consistent electrical performance, and ease of automated placement. The component features a low-profile design suitable for dense PCB layouts and is commonly used in prototyping, embedded systems, and production-level electronics. Design and Construction The connector is manufactured with precision-aligned contacts housed in a high-temperature thermoplastic body, enabling compatibility with standard reflow soldering processes. The contact system is engineered to ensure stable mechanical retention and consistent electrical conductivity, supporting repeated mating cycles without significant degradation. The materials used provide durability, resistance to thermal stress, and compliance with common industry standards for electronic components. Electrical Characteristics The device is intended to provide reliable signal transmission with minimal contact resistance. It supports low to moderate current applications typical of signal-level interconnections. The contact plating is designed to reduce oxidation and maintain stable electrical performance over time. Mechanical Features The connector is configured as a single-row socket with a defined pitch spacing suitable for standard header interfaces. Its surface-mount termination allows for secure attachment to printed circuit boards while minimizing required board space. The structure supports proper alignment during assembly and ensures consistent engagement with corresponding mating connectors. Applications This component is widely used in applications such as microcontroller boards, communication modules, sensor interfaces, and general-purpose electronic systems. It is suitable for both development environments and final product integration where dependable and space-efficient connectivity is required. Compliance and Reliability The SSW-122-02-G-S is designed to meet common industry requirements for environmental and mechanical reliability. It is typically compliant with RoHS standards and suitable for use in a variety of operating conditions encountered in commercial and industrial electronics. #commonpartslibrary #connector #header

14V Clamp 2.5A (8/20µs) Ipp Tvs Diode Surface Mount 2-X1SON (1x.60) TVS diode USB VBUS 5V TVS diode USB VBUS 5V ESD protection General Description The TPD1E05U06DPYR is a single-channel transient voltage suppression device designed to protect sensitive electronic components from electrostatic discharge (ESD) and other transient voltage events. It is engineered for high-speed signal applications, offering low capacitance to preserve signal integrity while providing robust protection. The device is suitable for integration into compact and portable electronic systems where space, reliability, and performance are critical. Device Identification Part number: TPD1E05U06DPYR Device classification: ESD protection diode / transient voltage suppressor Manufacturer: Commonly associated with Texas Instruments Mounting type: Surface-mount Package style: Ultra-small leadless package (e.g., X2SON/DFN) Functional Description Protects circuits from high-voltage transients caused by ESD events Limits voltage spikes by clamping them to safe levels Maintains signal quality by minimizing added capacitance Operates transparently under normal signal conditions Provides fast response to transient disturbances Performance Characteristics Low capacitance suitable for high-speed data lines High ESD protection capability compliant with standard test models Low leakage current during normal operation Fast transient response time Stable performance across specified operating conditions Electrical Characteristics Designed for low-voltage applications (approximately 5 V working range) Low clamping voltage to protect downstream components Minimal dynamic resistance Very low input/output capacitance High reliability under repeated ESD stress Application Scope High-speed communication interfaces such as USB, HDMI, and display ports Mobile phones, tablets, and wearable electronics Embedded systems and microcontroller interfaces Consumer and industrial electronic equipment Data and signal line protection in compact devices Mechanical and Physical Properties Compact footprint for high-density PCB layouts Leadless package for improved mechanical robustness Compatible with standard surface-mount assembly processes Designed for automated manufacturing environments Integration Guidelines Install as close as possible to the external connector or entry point Ensure a low-impedance path to ground for optimal protection Minimize trace length between the device and the protected line Consider layout practices to preserve high-speed signal integrity Verify compatibility with system voltage and interface requirements #commonpartslibrary #circuitprotection #tvsdiode

Accelerometer X, Y, Z Axis ±3g 1.6kHz (X,Y), 550Hz (Z) 16-LFCSP-LQ (4x4) The ADXL335BCPZ-RL7 is a low-power, complete 3-axis accelerometer with analog voltage outputs proportional to acceleration. It measures acceleration along the X, Y, and Z axes with a full-scale range of ±3 g. This device integrates a micro-electromechanical system (MEMS) sensor with signal conditioning circuitry, enabling direct analog output without the need for external amplification. The RL7 suffix indicates tape-and-reel packaging for automated assembly. The ADXL335BCPZ-RL7 is designed for compact, battery-powered, and motion-sensitive applications where low power consumption and ease of integration are critical. Functional Overview The accelerometer operates using a capacitive sensing structure. Acceleration causes displacement of an internal mass, changing capacitance, which is converted into a proportional analog voltage output. Each axis operates independently and provides a continuous analog signal that can be read by a microcontroller’s ADC. External capacitors allow the user to configure bandwidth per axis, enabling optimization for noise or response speed. Electrical Characteristics Supply Voltage Range: 1.8 V to 3.6 V Supply Current: Typical: 350 µA Measurement Range: ±3 g Sensitivity (Typical): 300 mV/g Zero-g Bias Level: Approximately VCC / 2 Bandwidth: Adjustable via external capacitors Typical limits: X, Y axes: up to 1600 Hz Z axis: up to 550 Hz Output Characteristics Output Type: Analog (ratiometric to supply voltage) Axes: Three independent outputs (XOUT, YOUT, ZOUT) Output Impedance: Approximately 32 kΩ Noise Density: X/Y axes: ~150 µg/√Hz Z axis: ~300 µg/√Hz Mechanical Characteristics Package Type: 16-lead LFCSP Package Dimensions: Approximately 4 mm × 4 mm × 1.45 mm Mounting: Surface mount Packaging Option: Tape and reel (RL7) Environmental Specifications Operating Temperature Range: −40°C to +85°C Storage Temperature Range: −65°C to +150°C Shock Survival: Up to 10,000 g Interface Requirements External Components: Capacitors required for bandwidth selection (one per axis) Interface Type: Analog voltage outputs compatible with ADC inputs Pin Description (Summary) ST: Self-test input XOUT: X-axis analog output YOUT: Y-axis analog output ZOUT: Z-axis analog output VCC: Power supply GND: Ground NC: No connection / reserved Applications Tilt and orientation sensing Motion and vibration detection Portable electronics Gaming controllers Wearable devices Industrial monitoring systems Key Features Three-axis acceleration measurement Low power consumption Analog output for simple interfacing Compact MEMS package Adjustable bandwidth Wide temperature operating range Tape-and-reel packaging for automated manufacturing #commonpartslibrary #integratedcircuit #sensor #accelerometer

Linear Voltage Regulator IC Positive Fixed 1 Output 500mA SOT-23-5 The TLV75533PDBVR is a low-dropout (LDO) linear voltage regulator designed to provide a stable 3.3 V output from a higher input voltage source. It features ultra-low quiescent current and high power-supply rejection ratio (PSRR), making it ideal for battery-powered and noise-sensitive applications such as IoT devices, portable electronics, and RF circuits. The device is optimized for fast transient response and stable operation with small ceramic output capacitors. Key Features Fixed output voltage: 3.3 V Low dropout voltage (typ. ~200 mV at full load) Ultra-low quiescent current (typ. 25 µA) High PSRR for noise-sensitive applications Stable with small ceramic capacitors (≥1 µF) Thermal shutdown and overcurrent protection Available in compact SOT-23-5 package (DBV) Absolute Maximum Ratings Input voltage: –0.3 V to 6.5 V Output voltage: –0.3 V to (VIN + 0.3 V) Operating junction temperature: –40°C to +125°C Storage temperature range: –65°C to +150°C Recommended Operating Conditions Input voltage range: 1.45 V to 5.5 V Output voltage: 3.3 V (fixed) Output current: up to 500 mA Operating temperature range: –40°C to +125°C Electrical Characteristics (Typical unless otherwise noted) Output voltage accuracy: ±1% Dropout voltage: ~200 mV @ 500 mA Quiescent current: ~25 µA PSRR: up to 70 dB (at 1 kHz) Line regulation: <0.05%/V Load regulation: <0.5% Pin Configuration (SOT-23-5) Pin 1: IN – Input voltage Pin 2: GND – Ground Pin 3: EN – Enable (active high) Pin 4: NC – No connect Pin 5: OUT – Regulated output Typical Application Power management for microcontrollers and sensors Battery-powered portable devices RF and analog circuits requiring low noise supply IoT and wearable electronics Protection Features Thermal shutdown protection Overcurrent protection Undervoltage lockout (UVLO) #commonpartsLibrary #integratedcircuit #powermanagement #voltageregulator

ARM® Cortex® M3 STM32F1 Microcontroller IC 32-Bit Single-Core 72MHz 64KB (64K x 8) FLASH Medium-density performance line Arm®-based 32-bit MCU with 64 or 128 KB Flash, USB, CAN, 7 timers, 2 ADCs, 9 com. interfaces Arm® 32-bit Cortex®-M3 CPU core – 72 MHz maximum frequency, 1.25 DMIPS/MHz (Dhrystone 2.1) performance at 0 wait state memory access – Single-cycle multiplication and hardware division • Memories – 64 or 128 Kbytes of Flash memory – 20 Kbytes of SRAM • Clock, reset and supply management – 2.0 to 3.6 V application supply and I/Os – POR, PDR, and programmable voltage detector (PVD) – 4 to 16 MHz crystal oscillator – Internal 8 MHz factory-trimmed RC – Internal 40 kHz RC – PLL for CPU clock – 32 kHz oscillator for RTC with calibration • Low-power – Sleep, Stop and Standby modes – VBAT supply for RTC and backup registers • 2x 12-bit, 1 µs A/D converters (up to 16 channels) – Conversion range: 0 to 3.6 V – Dual-sample and hold capability – Temperature sensor • DMA – 7-channel DMA controller – Peripherals supported: timers, ADC, SPIs, I 2Cs and USARTs • Up to 80 fast I/O ports – 26/37/51/80 I/Os, all mappable on 16 external interrupt vectors and almost all 5 V-tolerant Debug mode: – Serial wire debug (SWD) and JTAG interfaces • Seven timers – Three 16-bit timers, each with up to 4 IC/OC/PWM or pulse counter and quadrature (incremental) encoder input – 16-bit, motor control PWM timer with dead-time generation and emergency stop – Two watchdog timers (independent and window) – SysTick timer 24-bit downcounter • Up to nine communication interfaces – Up to two I2C interfaces (SMBus/PMBus®) – Up to three USARTs (ISO 7816 interface, LIN, IrDA capability, modem control) – Up to two SPIs (18 Mbit/s) – CAN interface (2.0B Active) – USB 2.0 full-speed interface • CRC calculation unit, 96-bit unique ID • Packages are ECOPACK #commonpartslibrary #integratedcircuit #microcontroller #stm32f1

Linear Voltage Regulator IC Positive Fixed 1 Output 150mA SOT-23-5 LP2985IM5-2.7 is a low-dropout (LDO) linear voltage regulator designed to provide a stable 2.7 V output with very low quiescent current and excellent noise performance. It is optimized for battery-powered and noise-sensitive applications, offering high power supply rejection ratio (PSRR) and fast transient response. The device is housed in a compact SOT-23-5 package, making it ideal for space-constrained designs. Key Features Fixed 2.7 V output voltage Low dropout voltage Low quiescent current (IQ) High PSRR for noise-sensitive applications Stable with low ESR ceramic capacitors Thermal shutdown and current limit protection Small SOT-23-5 package RoHS compliant Electrical Characteristics Output Voltage: 2.7 V (fixed) Output Voltage Accuracy: ±1.5% (typical) Maximum Output Current: 150 mA Dropout Voltage: ~280 mV at 150 mA (typical) Quiescent Current (IQ): ~65 µA (typical) Line Regulation: 0.04%/V (typical) Load Regulation: 0.2% (typical) PSRR: Up to 70 dB (at low frequency) Operating Input Voltage Range: 2.5 V to 16 V Operating Temperature Range: -40°C to +125°C Mechanical Characteristics Package Type: SOT-23-5 (DBV) Mounting Type: Surface Mount Pin Count: 5 pins Approximate Dimensions: 2.9 mm × 1.6 mm Pin Configuration (Typical) IN: Input voltage GND: Ground OUT: Regulated output (2.7 V) EN: Enable (active high) BYPASS: Noise reduction / bypass capacitor connection Performance Characteristics Excellent output noise performance (low-noise design) Fast transient response to load changes Stable with small ceramic capacitors (typically 1 µF) Suitable for RF and analog circuits Applications Battery-powered devices Portable electronics RF and wireless modules Sensors and analog circuits Microcontroller power supplies #CommonPartsLibrary #IntegratedCircuit #PowerManagement #voltage-regulator #LDO #LP3985

LED Lighting Driver ICs LED Lighting Drivers 4-Channel RGBW Driver, I2C, 1.5x1.5mm TDFN The KTD2027BEWE-TR is a highly integrated, low-power RGB LED driver designed for portable and battery-powered applications. It features a compact WLCSP package and provides precise current control for up to three LED channels. The device includes an I²C-compatible interface, enabling flexible control of brightness, color mixing, and lighting effects. Integrated features such as programmable current sinks, dimming control, and built-in protection mechanisms make it suitable for indicators, backlighting, and decorative lighting in consumer electronics. Key Features Triple-channel constant current LED driver (RGB support) I²C-compatible digital interface Independent brightness control per channel Programmable current up to ~24 mA per channel Built-in PWM dimming and pattern generation Low quiescent current for power-sensitive applications Wide input voltage range Thermal shutdown and overcurrent protection Small WLCSP package (suitable for compact designs) Applications Mobile devices and wearables Status indicators and notification LEDs Backlighting and decorative lighting IoT and portable electronics Absolute Maximum Ratings Supply Voltage (VDD): −0.3 V to +6.0 V Logic Input Voltage: −0.3 V to VDD + 0.3 V Operating Temperature Range: −40°C to +85°C Storage Temperature Range: −55°C to +150°C Recommended Operating Conditions Supply Voltage (VDD): 1.8 V to 5.5 V LED Forward Voltage: Dependent on external LEDs Ambient Temperature: −40°C to +85°C Electrical Characteristics (Typical) Supply Current (Idle): < 1 µA (shutdown mode) Channel Current Accuracy: ±5% (typical) Maximum Output Current: ~24 mA per channel I²C Clock Frequency: Up to 400 kHz (Fast Mode) Functional Description The KTD2027BEWE-TR operates as a constant-current sink driver for RGB LEDs. Each channel can be independently programmed via the I²C interface to control brightness and enable dynamic lighting effects. Internal PWM generators allow smooth dimming without requiring continuous microcontroller intervention. The device also integrates protection features such as thermal shutdown and current limiting to ensure reliable operation. Pin Configuration (Typical WLCSP) VDD – Power supply GND – Ground SDA – I²C data line SCL – I²C clock line LED1 – Current sink output (Red) LED2 – Current sink output (Green) LED3 – Current sink output (Blue) Package Information Package Type: WLCSP (Wafer-Level Chip Scale Package) Mounting: Surface mount Tape & Reel: Yes (TR suffix) Ordering Information KTD2027BEWE-TR: Tape and reel packaging for automated assembly #commonpartslibrary #integratedcircuit #leddriver

25 MHz ±30ppm Crystal 20pF 50 Ohms 4-SMD, No Lead The FL2500283Z is a 25 MHz surface-mount quartz crystal manufactured by Diodes Incorporated, part of the FL series (SaRonix-eCera™). It is designed for use as a stable clock reference in digital circuits such as microcontrollers, communication modules, and embedded systems. This crystal uses an AT-cut resonator inside a compact 3.2 mm × 2.5 mm (3225) ceramic package, making it suitable for high-density PCB designs and modern electronics. Key Features Standard Frequency 25 MHz fundamental mode crystal Compact SMD Package 3.2 × 2.5 mm (3225), 4-pad configuration Height ~0.68–0.75 mm AT-Cut Quartz Technology Provides good frequency stability and low drift Frequency Stability & Tolerance Typical: ±10 to ±30 ppm Load Capacitance Typically 20 pF Low ESR Around 50–60 Ω, suitable for MCU oscillator circuits Wide Operating Temperature Common range: -20°C to +70°C (some variants up to -40°C to +125°C) Surface-Mount Compatibility Ideal for automated assembly and reflow soldering RoHS / Lead-Free Environmentally compliant design Typical Applications Microcontroller clock (STM32, ESP32, AVR, etc.) Communication modules (Wi-Fi, Ethernet, RF) Embedded systems Consumer electronics Industrial control boards #Crystal #Oscillator #Resonator #SaRonix-eCera™ FL

16 Position Header Connector 0.100" (2.54mm) Through Hole, Right Angle Gold The PPPC082LJBN-RC is a dual-row, right-angle pin header connector intended for through-hole PCB mounting. It uses a standard 2.54 mm pitch with a 2×8 pin configuration and is commonly used for board-to-board or board-to-cable connections. The connector provides stable mechanical support and reliable electrical performance, making it suitable for prototyping, embedded systems, and general-purpose electronic designs. Mechanical Specifications Connector Type: Pin Header Mounting Type: Through-Hole, Right Angle Number of Positions: 16 (2×8) Pitch: 2.54 mm Row Spacing: 2.54 mm Contact Orientation: Right Angle Termination Style: Solder Housing Material: Thermoplastic (UL94V-0 rated) Contact Material: Brass Electrical Specifications Current Rating: Typically up to 3 A per contact Voltage Rating: Typically 250 V Contact Resistance: ≤ 20 mΩ Insulation Resistance: ≥ 1000 MΩ Dielectric Withstanding Voltage: ~500 VAC Environmental Specifications Operating Temperature Range: -40°C to +105°C Flammability Rating: UL94V-0 RoHS Compliance: Yes Plating Contact Plating: Gold flash over nickel (typical) Tail Plating: Tin over nickel Applications PCB interconnections Embedded systems and microcontroller boards Industrial control interfaces Consumer electronics prototyping Signal and low-power connections Mating Compatibility Compatible with standard 2.54 mm pitch female headers and IDC connectors #commonpartslibrary #connector #header