Microcontrollers

The YFW AO3400 is a 30V N-Channel Enhancement MOSFET designed for low-voltage and high-speed switching applications. It uses advanced trench MOSFET technology to achieve low on-resistance (RDS(on)), fast switching performance, and efficient power handling in a compact SOT-23 package. It is commonly used in load switching, DC-DC converters, battery-powered devices, motor control, LED driving, and PWM switching circuits. Key Features N-Channel Enhancement Mode MOSFET Drain-Source Voltage (VDS): 30V Continuous Drain Current (ID): up to 5.8A Low RDS(on): < 28mΩ @ VGS = 10V < 33mΩ @ VGS = 4.5V < 52mΩ @ VGS = 2.5V Logic-Level Gate Drive Compatible Fast Switching Speed Low Gate Charge Compact SOT-23 Package Suitable for PWM and Load Switch Applications RoHS / Pb-Free Compatible Typical Applications Power switching DC-DC converters Battery management systems Motor and fan control LED drivers Portable electronics Microcontroller-based switching circuits #CommonPartsLibrary #Transistor #FET #Mosfet

Battery Battery Monitor IC Lithium Ion 8-TDFN-EP (2x2) The MAX17048/MAX17049 ICs are tiny, micropower current fuel gauges for lithium-ion (Li+) batteries in handheld and portable equipment. The MAX17048 operates with a single lithium cell and the MAX17049 with two lithium cells in series. The ICs use the sophisticated Li+ battery-modeling algorithm ModelGauge™ to track the battery relative state-ofcharge (SOC) continuously over widely varying charge and discharge conditions. The ModelGauge algorithm eliminates current-sense resistor and battery-learn cycles required in traditional fuel gauges. Temperature compensation is implemented using the system microcontroller. The ICs automatically detect when the battery enters a low-current state and enters low-power 3µA hibernate mode, while still providing accurate fuel gauging. The ICs automatically exit hibernate mode when the system returns to active state. On battery insertion, the ICs debounce initial voltage measurements to improve the initial SOC estimate, thus allowing them to be located on system side. SOC, voltage, and rate information is accessed using the I2C interface. The ICs are available in a tiny 0.9mm x 1.7mm, 8-bump wafer-level package (WLP), or a 2mm x 2mm, 8-pin TDFN package. ● MAX17048: 1 Cell, MAX17049: 2 Cells ● Precision ±7.5mV/Cell Voltage Measurement ● ModelGauge Algorithm • Provides Accurate State-of-Charge • Compensates for Temperature/Load Variation • Does Not Accumulate Errors, Unlike Coulomb Counters • Eliminates Learning • Eliminates Current-Sense Resistor ● Ultra-Low Quiescent Current • 3μA Hibernate, 23μA Active • Fuel Gauges in Hibernate Mode • Automatically Enters and Exits Hibernate Mode ● Reports Charge and Discharge Rate ● Battery-Insertion Debounce • Best of 16 Samples to Estimate Initial SOC ● Programmable Reset for Battery Swap • 2.28V to 3.48V Range ● Configurable Alert Indicator • Low SOC • 1% Change in SOC • Battery Undervoltage/Overvoltage • VRESET Alert ● I2C Interface ● 8-Bit OTP ID Register (Contact Factory) #CommonPartsLibrary #IntegratedCircuit #PowerManagement #Battery-management #MAX17048

CRYSTAL 8MHz 8pF SMD The NX3225GD-8MHZ-STD-CRA-3 is an automotive-grade surface-mount quartz crystal unit from NDK designed to provide a stable 8 MHz clock reference for microcontrollers, automotive ECUs, and embedded systems. It belongs to the NX3225GD series and is optimized for high reliability under harsh environmental conditions. Key Features 8 MHz fundamental-mode crystal Compact 3.2 mm × 2.5 mm × 1.0 mm SMD package 8 pF load capacitance ±50 ppm frequency tolerance ±150 ppm frequency stability over temperature Automotive-qualified with AEC-Q200 compliance Wide operating temperature range: −40°C to +150°C Excellent resistance to heat, vibration, shock, and solder cracking Stable startup characteristics in severe environments RoHS compliant Typical Applications Automotive engine control units (ECUs) MCU and CPU clock generation Industrial embedded systems Communication equipment Consumer electronics and IoT devices #CommonPartsLibrary #crystal oscillator #resonator

ESD DIODE 15VC SOT-23-6 The UMW USBLC6-2SC6 is a low-capacitance TVS/ESD protection diode array designed to protect high-speed data interfaces such as USB 2.0 and Ethernet from electrostatic discharge (ESD), electrical fast transients (EFT), and surge events. It integrates dual protection channels in a compact SOT-23-6 package, making it suitable for space-constrained portable and embedded designs. Key Features Dual-line ESD protection for high-speed signal interfaces Supports USB 2.0, 10/100 Ethernet, and other sensitive data lines Very low capacitance (~0.8 pF typical) to preserve signal integrity Operating voltage: 5 V Low clamping voltage for improved downstream IC protection IEC 61000-4-2 ESD protection: ±30 kV air discharge ±30 kV contact discharge IEC 61000-4-4 EFT protection up to 40 A (5/50 ns) IEC 61000-4-5 surge protection up to 6 A (8/20 µs) Peak pulse power capability: 150 W Ultra-low leakage current in the nA range Fast response time (<1 ns typical) Compact SOT-23-6 surface-mount package RoHS, Pb-free, and halogen-free compliant Typical Applications USB data line protection Ethernet interfaces Portable electronics Notebook and desktop PCs Digital cameras Embedded systems and microcontroller USB ports #CommonPartsLibrary #TVS-Diode

680 kOhms ±5% 0.25W, 1/4W Through Hole Resistor Axial Automotive AEC-Q200 Carbon Film The CFR-25JB-52-680K is a carbon film through-hole resistor designed for general-purpose electronic applications requiring stable resistance characteristics, reliable long-term performance, and cost-effective implementation. This resistor is commonly used in signal conditioning, voltage division, pull-up and pull-down networks, biasing circuits, and low-power analog or digital systems. Its axial leaded construction supports automated insertion and conventional through-hole assembly methods, making it suitable for consumer electronics, industrial controls, instrumentation, and embedded systems. The device utilizes carbon film resistive technology to provide dependable electrical performance with moderate noise characteristics and good environmental stability. The flame-retardant coating enhances mechanical durability and improves resistance against moisture and environmental exposure. The component is optimized for standard operating environments where compact size, stable operation, and economical design are required. Electrical Characteristics Resistance Value: 680 kΩ Resistance Tolerance: ±5% Resistor Technology: Carbon Film Rated Power Dissipation: 1/4 W Maximum Working Voltage: 250 V Maximum Overload Voltage: 500 V Temperature Coefficient: ±350 ppm/°C Insulation Resistance: High reliability insulation structure suitable for general electronic equipment Mechanical Characteristics Package Type: Axial Through-Hole Mounting Style: Through Hole Body Style: Cylindrical Flame-Retardant Coated Body Lead Material: Tin-Plated Copper Lead Configuration: Axial Leads for PCB insertion Environmental Characteristics Operating Temperature Range: −55°C to +155°C Moisture Resistance: Suitable for standard humidity environments Flame Resistance: Flame-retardant protective coating compliant with general safety requirements Applications Signal Conditioning Circuits Voltage Divider Networks Pull-Up and Pull-Down Resistors Industrial Control Electronics Consumer Electronic Products General Analog and Digital Circuitry Embedded Systems and Microcontroller Interfaces #commonpartslibrary #passivecomponents #resistor #carbonfilm #throughhole #axialresistor #powermanagement #analog #digital #industrialelectronics

Humidity, Temperature 0 ~ 100% RH I2C ±1.8% RH 4 s Surface Mount The SHT41-AD1B-R3 is a high-precision digital humidity and temperature sensor developed by Sensirion. It integrates calibrated sensing elements, analog signal processing, and a digital communication interface within a compact surface-mount package optimized for space-constrained embedded applications. The device is designed for accurate environmental monitoring across industrial, consumer, HVAC, portable electronics, and IoT systems. The sensor utilizes Sensirion CMOSens® technology to provide stable long-term performance, fast response time, and excellent repeatability under varying environmental conditions. Factory calibration enables direct digital output without the need for external calibration circuitry. The integrated I²C interface simplifies system integration with microcontrollers and embedded processors. The SHT41-AD1B-R3 is engineered for low-power operation, making it suitable for battery-powered and energy-efficient designs. Its compact DFN package supports automated assembly processes and high-density PCB layouts. The device also incorporates advanced internal diagnostics and checksum protection to improve communication reliability and data integrity. Features High-accuracy relative humidity sensing High-accuracy temperature measurement Fully calibrated and linearized digital output I²C digital communication interface Low power consumption optimized for portable systems Fast response and measurement conversion time Excellent long-term stability and repeatability Integrated heater functionality for condensation mitigation Wide operating voltage range Compact surface-mount DFN package Factory-trimmed and tested performance High immunity to environmental stress and contamination Low drift over product lifetime Suitable for reflow soldering processes Electrical Characteristics Supply voltage supports low-voltage embedded systems Digital communication compatible with standard I²C hosts Low standby current consumption Optimized active measurement current Integrated CRC data protection for communication integrity Environmental Characteristics Wide operating temperature range Wide relative humidity operating range Designed for high reliability in industrial and consumer environments Resistant to moisture-induced performance degradation Supports long operational lifetime with stable calibration Package Information Compact DFN surface-mount package Moisture-sensitive device suitable for automated assembly RoHS compliant and halogen-free construction Tape-and-reel packaging configuration for production assembly Applications Environmental monitoring systems HVAC and climate control equipment Smart home and IoT devices Portable electronics Industrial automation systems Data loggers and instrumentation Weather monitoring equipment Indoor air quality monitoring Battery-powered sensor nodes Consumer electronic products #commonpartslibrary #sensor #temperature #humidity #environmentalsensor #i2c #embedded #industrial #iot #sensirion

ARM® Cortex®-M7 S32K3 Microcontroller IC 32-Bit 160MHz 4MB (4M x 8) FLASH 172-QFP (16x16)

16 Bit Digital to Analog Converter 1 10-VSSOP The DAC80501MDGSR is a high-precision, single-channel digital-to-analog converter developed by Texas Instruments for industrial, instrumentation, and embedded control applications requiring accurate voltage output generation. The device integrates a low-drift voltage reference, precision output buffer, and serial peripheral interface communication into a compact low-power solution optimized for high-resolution signal generation. Designed for applications such as programmable power supplies, process control systems, automated test equipment, and sensor calibration, the device delivers excellent linearity, low noise performance, and stable output characteristics across varying environmental conditions. The integrated architecture minimizes external component requirements while maintaining high accuracy and long-term reliability. The converter supports rail-to-rail output operation and offers flexible reference configurations to accommodate different system architectures. Its SPI-compatible digital interface enables straightforward integration with microcontrollers, processors, and FPGA-based systems. Electrical Characteristics The device operates from a single analog supply and supports precision voltage output generation with monotonic performance across the full operating range. Integrated precision reference circuitry provides low temperature drift and stable output characteristics suitable for high-accuracy measurement and control systems. Low glitch energy, low offset error, and low gain error characteristics improve output stability during code transitions. The output amplifier is capable of driving moderate capacitive loads while maintaining signal integrity and settling performance. Interface and Control Communication is implemented through a high-speed SPI-compatible serial interface supporting standard synchronous digital communication protocols. The interface allows direct programming of DAC output codes and internal configuration registers. The device supports daisy-chain capable serial communication architecture for simplified expansion in multi-device systems. Internal registers provide control of reference operation, power management, and output configuration functions. Power Management The DAC80501MDGSR incorporates low-power operating modes intended for energy-sensitive applications. Integrated power-down functionality reduces current consumption during inactive system states while preserving configuration integrity. Internal circuitry is optimized for low quiescent current operation without compromising output precision or dynamic response performance. Package Information The device is supplied in a compact VSSOP surface-mount package suitable for space-constrained industrial and embedded designs. The package configuration supports automated assembly processes and standard PCB manufacturing techniques. Typical Applications Typical applications include industrial automation, programmable voltage sources, data acquisition systems, sensor simulation, instrumentation equipment, motor control systems, and precision calibration platforms. The device is particularly suitable for systems requiring stable and repeatable analog voltage generation with minimal external circuitry. #commonpartslibrary #integratedcircuit #analog #digital #converter

24 Bit Analog to Digital Converter 8 Input 8 Sigma-Delta 32-TQFP (5x5) The ADS131M08IPBSR is a high-precision, simultaneous-sampling analog-to-digital converter designed for multi-channel data acquisition systems requiring accurate and synchronized measurements. Manufactured by Texas Instruments, this device integrates eight differential input channels with low-noise performance, programmable gain amplification, and precision voltage reference support. The converter architecture is optimized for industrial automation, energy monitoring, medical instrumentation, and precision sensing applications where phase alignment and signal fidelity are critical. The device incorporates delta-sigma conversion technology with integrated digital filtering to provide high dynamic range and excellent noise performance across a wide operating bandwidth. It supports flexible data interface configurations through a high-speed SPI-compatible serial interface, enabling efficient communication with microcontrollers, DSPs, and FPGA-based systems. The integrated diagnostic and monitoring features improve system reliability and simplify fault detection in safety-critical applications. The ADS131M08IPBSR operates from low-voltage analog and digital supplies while maintaining low power consumption suitable for embedded and portable systems. The compact thermally enhanced package supports dense PCB layouts and reliable operation across industrial temperature environments. Engineering Specification Device Type: Simultaneous-Sampling Delta-Sigma Analog-to-Digital Converter Manufacturer: Texas Instruments Channel Configuration: Eight Differential Input Channels Resolution: Twenty-Four Bit ADC Architecture: Delta-Sigma Sampling Type: Simultaneous Sampling Input Type: Differential Analog Inputs Programmable Gain Amplifier: Integrated Data Output Interface: SPI-Compatible Serial Interface Reference Support: External Precision Voltage Reference Digital Filtering: Integrated Sinc Filter Architecture Operating Supply Voltage: Low-Voltage Analog and Digital Supplies Noise Performance: Low Noise Precision Measurement Capability Power Consumption: Optimized for Low Power Operation Diagnostics Features: Integrated Self-Monitoring and Fault Detection Temperature Range: Industrial Operating Temperature Range Package Type: TQFP Surface-Mount Package Mounting Type: Surface Mount Technology Application Areas: Energy Metering, Industrial Automation, Medical Instrumentation, Data Acquisition Systems, Multi-Channel Sensor Interfaces #commonpartslibrary #integratedcircuit #analog #digital #converter

Accelerometer X, Y, Z Axis ±2g, 4g, 8g 6.25Hz ~ 200Hz 12-LGA (2.2x2.3) The ADXL367BCCZ-RL7 is an ultra-low power, three-axis MEMS accelerometer developed by Analog Devices for motion sensing applications requiring extremely low energy consumption and high measurement stability. The device integrates precision acceleration sensing, embedded motion detection capabilities, and intelligent power management features within a compact surface-mount package suitable for portable and battery-operated systems. The accelerometer supports both I²C and SPI digital communication interfaces, enabling flexible integration with embedded processors, microcontrollers, and sensor hubs. Its architecture is optimized for continuous motion monitoring while maintaining exceptionally low current consumption, making it ideal for wearable electronics, asset tracking devices, medical monitoring equipment, industrial sensing systems, and Internet of Things platforms. The device incorporates embedded activity, inactivity, and wake-up detection functions that allow host processors to remain in low-power states until significant motion events occur. Integrated FIFO buffering and programmable interrupt functionality reduce processor overhead and improve overall system efficiency. The ADXL367BCCZ-RL7 is designed for robust operation across a wide operating temperature range and maintains high measurement accuracy with low noise and excellent long-term stability. The compact LGA package enables dense PCB layouts for space-constrained designs. Key Features Motion Sensing Three-axis digital accelerometer Selectable acceleration measurement ranges High-resolution motion detection Low noise sensing architecture Integrated temperature sensor Power Management Ultra-low power operation optimized for battery-powered systems Multiple operating and standby modes Autonomous motion-triggered wake-up capability Efficient duty-cycling support Digital Interfaces Supports SPI communication Supports I²C communication Programmable interrupt outputs Embedded FIFO data buffering Embedded Detection Functions Activity detection Inactivity detection Motion-triggered interrupt generation Autonomous wake-up monitoring Mechanical and Environmental Compact LGA surface-mount package High shock tolerance Wide operating temperature capability Suitable for portable and industrial environments Electrical Characteristics Supply Requirements Low-voltage digital supply operation Optimized for low-current embedded systems Stable operation across supported voltage range Sensor Performance High sensitivity stability Low offset drift Low output noise density Configurable output data rates Communication and Control Supported Interfaces SPI serial interface I²C serial interface Programmability Configurable measurement ranges Adjustable output data rates Programmable interrupt mapping FIFO configuration support Package Information Package Type LGA surface-mount package Mounting PCB surface mount compatible Suitable for automated assembly processes Typical Applications Wearable electronics Health and fitness monitoring Portable instrumentation Asset and condition monitoring Industrial sensing systems IoT sensor nodes Motion-activated devices Battery-powered embedded systems #commonpartslibrary #integratedcircuit #accelerometer #sensor